Problem Description Using a special device, the valve in a pipe line is to be opened and closed. The valve is opened by pressing the pushbutton switch. When the pushbutton is released, the valve is closed. Drawing the pneumatic and electric circuit diagram Carrying out the pneumatic and electric circuit construction Checking the sequence of the circuit

Q: Which of the following is a symbol of the valve which continuously, resisting its flow even after…

A: Solution:

Q: poad the aeasarement of the Micometer (b) 20 15 0-25 mm

A: Metrology Metrology is the branch of science which deals with the measurements. Metrology is the key…

Q: What is the purpose of using modes that control or limit "pressure delivery" with each breath in a…

A: The mechanical ventilator is a device used to regulate the optimum gases in the lungs. The working…

Q: Identify the true statement from the following O Venturimeter is a rate of flow measuring instrument…

A: # Venturimeter is used for flow measuring not for Rate of flow so this statement wrong #venturimeter…

Q: give me actual picture base on this circuit, they are cylinder, doublr solenoid valve, check valve,…

A: Given:To find:Draw the actual picture of the double pump circuit.

Q: What does the schematic symbol below representing?

A:

Q: What do the letters: A, B, P, T, E stand for in relation to a four-way valve?

A: The 4-Way Directional Valve block represents a directional control valve with four ports and three…

Q: Because of not being able to access the entire internal part of a pipe, this type of equipment is…

A: The question is asking about a type of equipment that is difficult to inspect internally due to…

Q: In pitot tube, the flowing fluid touches the pitot tube ________________ pressure reaches zero…

A: Pitot tube is a device which is used to measure the flow velocity.

Q: Why would we want to add a load resistor to the potentiometer circuit?

A: Step 1:Anti-Loading Effect: The potentiometer has a loading effect when connected to the load, which…

Q: D) What is the fastest that the accumulator could be charged by the pump to X = 0.1 m?

A:

Q: ons: In what situations would a circuit with multiple system pressu Are there any disadvantages to a…

A: 3. Hydraulic pressure is expressed as a force per unit of area, such as bar (kg/cm2) or PSI…

Q: Pressure control valves determine maximum system pressure True False

A:

Q: Explain the function of the fan in making the vacuum cleaner work.

A: Low air pressure is used by vacuum cleaners to assist us pick up minute particles of dirt and…

Q: Meter-out of pneumatic circuits utilizes check valve in only single direction. Select one: O True O…

A: We have to determine true/false

Q: What is thermocouple gauge used for detection of leaks in vacuum systems.

A:

Q: What are the funtions of an isolation/dump valve?

A:

Q: Industrial Pipes In order for there to be interchangeability between different components of a pipe,…

A: The objective of the question is to understand whether the pressure class and the gauge of different…

Q: V4 M TAD HD V1 M CYL. 2 FRL M AIH CYL. 1 M V3 LID V2

A:

Q: The A/C compressor cycles rapidly, and air coming from the vents is only slightly cool. Technician A…

A: The technician A is right.

Q: Static seals are used to improve the internal and external leakages of the non moving parts. Select…

A: The seals in hydraulics are used to avoids the leakage of any fluid (oil, lubricant, or any other…

Q: A fixed rating pressure switch is adjusted inside the pressure control and display console to record…

A: Fixed rating pressure switch cannot be adjusted inside the pressure control because due to fixed…

Q: While calculating the pressure difference for stack effect for a building with more openings in the…

A: Stack effect is used in the building to create natural ventilation, As cooler air is drawn into…

Q: Match the following in the right order

A: Given below solution Explanation:Step 1: Step 2: Step 3: Step 4:

Q: Choose the correct answer The discharge pressure of a refrigerant should be as constant as possible…

A:

Q: 10. Identify the number of ways, number of positions and the actuation method for each of the…

A: Figure 1:

Q: When oil pressure is below the spring pressure, the switch opens and the gauge reading falls toward…

A: It is False.

Q: After exchanging the adjustable one-way flow control valve 1V2 in the control circuit shown the…

A: Given a Pneumatic circuit diagram: To determine: The effect of the mistake on the operation of the…

Q: What are the types of air distribution system? Draw the diagram for each type

A:

Q: The wall thickness of a pipe is referred to as the pipe's __________.

A: Thickness of the pipe is nothing but the difference between outer radius and inner radius.

Q: Choose correct answer: Which one of the following devices creates only flow? An external gear…

A: External gear pumps are  used for pumping water and other fluids. They are preferred in applications…

Q: short objecytive of pneumatic circuits

A: Answer- A pneumatic circuit is an interconnected set of  components that converts compressed gas…

Q: what is the changing of diammeter of piping

A: Different pipe fittings are used in the piping networks to achieve transverse, bends, branches, and…

Q: Two cylinders A and B are actuated by solenoid activated spring-return 4/2 valves and controlled by…

A:

Q: Choose the correct answer The discharge pressure of a refrigerant should be as constant as possible…

A: In a refrigeration cycle the refregerant flows through the pipes into the compressor where it…

Q: The gas has the pressure of 120 bar and critical pressure of 60 bar, then the reduced pressure of…

A: Given               Pressure = 120 bar  Critical pressure= 60 bar

Q: Write the name of each of the following systems and its plant type (use A, B, C, D ). Condensate…

A: A. Steam generation cycle.

Q: * The value of (VSWR) is in the range of 1 to 0 0 to 0 -00 to o -1 to 1 O

A:

Q: Heavy internal springs are used to establish the operating pressure of the -operated type of…

A: In  hydraulic system pressure is controlled by metering the flow of fluid into or out of…

Q: Industrial pipes What precautions should be taken when opening a supply valve from a…

A: The objective of the question is to understand the safety measures that need to be taken while…

Q: Name and sketch the three types of plug gauges

A:

Q: How many throttles are in aircraft

A: A throttle level is basically by which the pilot controls the amount of fuel that is provided to the…

Q: For this valve schematic, what is the center position type O 1. No center O 2. Floated O 3. Locked O…

A:

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.