Problem :- A vehicle wheel with weight W attached to it through a spring, it is rolling along a wavy surface with constant speed (v = 18.25 m/sec) the static deflection of the spring under the load W is 9.8 cm and the wavy surface is given by the [h= H cos (wt)], where ▸ the wave length of the wavy surface = 183 cm and H=2.5 cm. Determine the amplitude of the forced vibration. K = 2.3 x 105 H = 2.5 cm h stimo W

Problem :- A vehicle wheel with weight W attached to it through a spring, it is rolling along a wavy surface with constant speed (v = 18.25 m/sec) the static deflection of the spring under the load W is 9.8 cm and the wavy surface is given by the [h= H cos (wt)], where ▸ the wave length of the wavy surface = 183 cm and H=2.5 cm. Determine the amplitude of the forced vibration. K = 2.3 x 105 H = 2.5 cm h stimo W

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use the slope-deflection method to analyze the contimuous beam shown in the Figure below. Draw the ahear and bending moment diaeram and sketch the elastic curve. El in constant. 30 kN 20 kN 20 kN/m 15 kN/m B 2.5 m 7 m 3 m 8m
Problem 41: Determine the maximum slope and maximum deflection for the beam shown in figure by conjugate beam method. Also find slope and deflection at B. A 1.2m B 10kN/m Kom 1.8m с
V= 31 X= 475 V/5 = 31/5 =6.2 %3D Y=155 V/10 = 3.1 2Y = 310 Z= 60 W = 25 %3D W4 = 6.25 lovtY = 10x31 + 155 =465 そ+W-60+25=85 YW= 31x25 = 775 %3D 1OZ = 10X 60 = 600
The beam shown is supporting a uniform load of 1.5 KN/m on the overhang BC. If E=200,000 MPa, l=7.5x10^6 mm^4. Using conjugate beam method determine the following: A. Compute the slope at point C. Express your answer in radians. B. Compute the deflection at point C. Express your answer in millimeters. 1.5kN/m B 6m 4m
2. A simply supported beam carries a load as shown in the figure below. What is the value of deflection and slope at point B if E = 200 GPa and the beam cross section is 300 mm by 550 mm. Use Moment-Area Method. 60 kN 32 kN / m El В 1.2 El 4 m 2 m 2 m
2.50) A 12 m simply supported beam with 30 kN load @ the center, if EI = 6000kN * m ^ 2 what is the maximum deflection? A. 150 mm C. 170 mm B. 160 mm D. 180 mm 2.51) A 2 in by 4 in rectangular bar is subjected to a bending load of 10 kN·m, find moment of inertia of the bar. A. 9.67 in C. 12.33i * n ^ 4 B. 10.67 in D. 14.33i * n ^ 4 A 10 m simply supported beam with 25 KN load is 3 m from the left end, what is the maximum 2.52) slope at the left end (EI = 8000kN * m ^ 2) ^ prime C. 0.0765 rad D. 0.1823 rad
The beam shown below is subjected to two 4 kN concentrated loads located 1.5 meters from each support. The bending moment diagram for the beam is plotted. Using the moment-area method, determine the deflection at point С. (A Assume E=200GPA, I=4×106 mm4) 4 kN 4 kN VD А В D00. 1.5 m 3 m 1.5 m 6 Bending Moment Diagram (kN.m) +
500 kN 100 kN-m A B C 1 m 2 m 1 m A simply supported prismatic beam is loaded as shown in the figure. Assume El = 1 x 10^6 kN.m^2 Compute the deflection of the at point D.
2. A simply supported beam carries a load as shown in the figure below. What is the value of deflection and slope at point B if E = 200 GPa and the beam cross section is 300 mm by 550 mm. Use Moment-Area Method. 60 kN 32 kN / m A El В 1.2 EI 4 m 2 m 2 m
A 10-m simply supported beam is loaded with 25Kn at midspan. Determine its maximum deflection in mm if El is equal to 6000000 N-m^2.
Problem 5 Determine the maximum deflection of the simply supported beam shown below using double integration method. 1 m 2 m 600 kN 400 kN/m А. 6 m 2 m Question 14 Determine the maximum deflection of the beam shown above. Ans.: El8 = Blank 1 kN.m3
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C. Assume I 800 x 106 mm and E = 70,000 MPa. %3D W1 BO C 8m 8 m 4 m 4 m W1 (kN/m) F (kN) s (mm) 20 60 25 If there is a settlement of S at the support C, solve the following using slope deflection method: 3. Reaction at A, RA in kN. 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m