Determine the maximum reaction at support B, the maximum shear at point C and the maximum positive moment that can be developed at point C on the beam shown due to: "a single concentrate live load of 8000 N "a uniform live load of 3000 N/m (applied on specific area: say positive area or negative area only) "a beam weight (dead load) of 1000 N/m (applied on the entire beam) A C B 4 m 5m 4 m

Determine the maximum reaction at support B, the maximum shear at point C and the maximum positive moment that can be developed at point C on the beam shown due to: "a single concentrate live load of 8000 N "a uniform live load of 3000 N/m (applied on specific area: say positive area or negative area only) "a beam weight (dead load) of 1000 N/m (applied on the entire beam) A C B 4 m 5m 4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The flexibility matrix for the beam shown in the figure is: 2 EI 1 3 2 EI 2EI 3ΕΙ 2ΕΙ (b) -L2 L (a) 2EI 3EI 2E1 ΕΙ 4E1 -6ΕΙ 7- 3EI 2EI Cc) (d) -6EI 12EI 2ΕΙ ΕΙ
Quizs- Replace the loading system by an equial ent resultant force and Couple moment acting at Point o. fi=l00 N Mc:75 Nm 0:3m 200 0-5 m 0.4m
Fig. P3.48 0.4 m 0.1 m B 0.3m 150 N-m 60 Nm Hibbeler F5-55. The assembly is made of A-36 steel and consists of a solid rod 20 mm in diameter fixed to the inside of a tube using a rigid disk at B. Determine the angle of twist at C. The tube has an outer diameter of 40 mm and wall thickness of 5 mm.
Subject: Date: 10KN 4 KN /m 6 m -3m K-Iim-* 3m 3m Figure I Figure 1 shows the Simply supported beam AB-Petermine a) support reaction a+ A b) Support reaction at
STRUCTURAL PART Interactive Question Choose the correct answer of the bending moment diagram of the Frame Below (Ignore Self weight) (A) B A Prepared By: ENG. MODAR HAJYOUNES Prepared By: ENG. SULAIMAN WARDAH C Prepared By :Eng. Moda Hajyounes B -A Another Unstable D E
B 300 mm ↑ 15 mm 70 KN 70 KN 20 mm 500 mm Steel Aluminum AMIN ATTIV 70 kN 70 KN + Rc A steel rod (20 mm diameter) 500 mm long is connected to two parallel aluminum rods (15 mm diameter) each 300 mm long via a rigid plate as shown. Two 70 kN loads at applied at the end of each aluminum rod. The structure is fixed at both ends resulting in a statically indeterminate system that can be treated as the superposition of two determinate systems as presented above. Note that Rc is the reaction at C. Assume Esteel = 200 GPa and Ealuminum = 70 GPa. a) Determine the reaction force at C, Rc b) Determine the reaction force at A and B and the normal stress in the steel and aluminum rods c) Which rods are in tension and which are in compression?
Determine the reactions for the following loaded beam , 2ym 5 N JO Nm A B TON Im 2m Im 1-5m
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the reaction at the left support (in kN-m). Sm sm steel holu circalar D I0o mn Di 80 mm dhaminum Selid circular D= 35 mv
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
B 300 mm 15 mm 70 kN 70 kN 20 mm ↑ 500 mm с Steel Aluminum 70 KN + f 70 KN Re A steel rod (20 mm diameter) 500 mm long is connected to two parallel aluminum rods (15 mm diameter) each 300 mm long via a rigid plate as shown. Two 70 kN loads at applied at the end of each aluminum rod. The structure is fixed at both ends resulting in a statically indeterminate system that can be treated as the superposition of two determinate systems as presented above. Note that R, is the reaction at C. Assume Esteel = 200 GPa and Ealuminum = 70 GPa. a) Determine the reaction force at C, Re b) Determine the reaction force at A and B and the normal stress in the steel and aluminum rods c) Which rods are in tension and which are in compression?
Calculate the support reaction VB ONLY, calculate SF at critical points and draw ONLY SFD for the beam shown in the figure of below 10 kN 24 kN-m D II A 1.5 m 4 m 2 m
Q1: A torque T = 4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa. Determine: (a) maximum shearing stress in the in the steel core. (b) the maximum shearing stress in the aluminum jacket. (c) the angle of twist at A. 172 mm 54 mm- A Steel core- 25 m Aluminum Q2: aluminum rod AB (G=27GPa) brass rod BD (G= 39GPa). portion CD of the brass rod is hollow and has an inner diameter of 40 mm, Determine: a) the angle of twist at A. b) maximum shear stress of rod AD c) torque diagram d) angle of twist diagram 60 mm TB 1600 Nm 36 mm T₁ = 800 Nm. 400 mm q+ 375 mm 250 mm