Problem (8.2): Calculate the maximum deflection 8max of a uniformly loaded simple beam as shown in Figure (8.22), if the span length L=2.0 m, the intensity of the uniform load q=2.0 kN/m, and the maximum bending stress o =60 MPa. The cross section of the beam is square, and the material is aluminum having modulus of elasticity E=70 GPa. q = 2.0 kN/m IIII L = 2.0 m Figure (822)

Problem (8.2): Calculate the maximum deflection 8max of a uniformly loaded simple beam as shown in Figure (8.22), if the span length L=2.0 m, the intensity of the uniform load q=2.0 kN/m, and the maximum bending stress o =60 MPa. The cross section of the beam is square, and the material is aluminum having modulus of elasticity E=70 GPa. q = 2.0 kN/m IIII L = 2.0 m Figure (822)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel beam is loaded as shown in the figure. Use conjugate beam method and determine the following: a. Slope at A b. Slope at B c. Displacement at the point of application of the 15KN load d. Displacement at C e. Location and maginitude of maximum deflection 15 kN 1.10 kN/m 2EI 2 m 2 m 2 m
The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b = 4.9 in., d = 4.7 in., and t = 0.31 in. The internal bending moment about the z centroidal axis is M, = -3.60 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. y ((ур.) d a a Answers: (a) Omax T= psi (b) Отax C psi
The simply supported beam is subjected to the loadings shown in Figure Q2. Determine the value of P if the allowable shear stress is 50 MPa. 20 mm PAN 30 kN/m 20 m 200 mm 20 mm 5m 5m 100 mm Crosssection Figure Q2
The following statement is true or false? Transverse shear forces in beams cause non-linear shear stress distributions over the cross section. True False
3. A steel beam is loaded as shown in the figure. Use conjugate beam method and determine the following: a. Slope at A b. Slope at B c. Displacement at the point of application of the 15kN load d. Displacement at C e. Location and maginitude of maximum deflection 15 kN 1.10 kN/ m 28 9/9 2 m 2 m 2 m
The cross-sectional dimensions of the beam shown in the figure are a = 4.3 in., b = 5.3 in., d = 4.2 in., and t = 0.32 in. The internal bending moment about the z centroidal axis is M, = -4.40 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. y (tур.) Answers: (а) ОтaxT psi (b) Omax C= psi
The cross-sectional dimensions of the beam shown in the figure are a = 4.0 in., b = 4.7 in., d = 4.1 in., and t = 0.30 in. The internal bending moment about the z centroidal axis is Mz = -3.90 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam.
In the given figure, a cantilever beam has annular cross-section. The ratio of the inner diameter of the section to the outer diameter is d, ld, = 0.6 and the shear modulus of the material is G= 80GPA. If the allowable shear stress is t=100 MPa, and the maximum allowable twist angle is 2=1.8°. 20kNm 19 kNm 11 kNm →z a) Calculate the cross section dimensions d, and d, values. D B 2m 4m 3m b) Draw the stress distribution on the most critical cross section according to the dimensioning. d. kiriş enkesiti
A 3m long simply supported beam of uniform cross section is subjected to a distributed uniformly w= 20 kN/m in the central 1m as shown load of in the figure. w= 20KN/m EI = 30x106 Nm? 1m 1m 1m If the flexural rigidity (EI) of the beam is 30x10 N-m?, the maximum slope (expressed in radians) of the deformed beam is
A horizontal bar, fixed at one end (x = 0), has a length of 1 m. and cross-sectional area of 100 mm2.Its elastic modulus varies along its length as given by E(x) = 100e-x GPa, where is the length coordinate (in m) along the axis of the bar. An axial tensile load of 10 KN is applied at the free end (x = 1).What is the axial displacement of the free end.
The cross-sectional dimensions of the beam shown in the figure are a = 4.5 in., b = 5.4 in., d = 4.9 in., and t= 0.31 in. The internal bending moment about the z centroidal axis is M, = -3.85 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. (typ.) Answers: (a) Omax T = psi (b) OmaxC= psi
2. Assuming that the three shape shown are identical (same allowable torsional stress, same cross sectional area and same thickness. What shape is the most efficient in terms of torque applied and by how much (%) in each of the other shape? ADO a 60° 60 a