Problem 5.127: (Munson, et al. 6th ed.) Water flows steadily down the inclined pipe as indicated below. Determine the following: (a) the difference in pressure P₁ - P2, (b) the loss between sections (1) and (2), and (c) the net axial force exerted by the pipe wall on the flowing water between sections (1) and (2). Flow Section (1) 5 ft

Problem 5.127: (Munson, et al. 6th ed.) Water flows steadily down the inclined pipe as indicated below. Determine the following: (a) the difference in pressure P₁ - P2, (b) the loss between sections (1) and (2), and (c) the net axial force exerted by the pipe wall on the flowing water between sections (1) and (2). Flow Section (1) 5 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A pipe 100 mm bore diameter carries oil of density 900 kg/m³ at a rate of 4 kg/s. The pipe reduces to 60 mm bore diameter and rises 120 m in altitude. The pressure at this point is atmospheric (zero gauge). Assuming no frictional losses, determine: i. The volume/s (4.44 dm³/s) 11. The velocity at each section (0.566 m/s and 1.57 m/s) 1. The pressure at the lower end (1.06 MPa) 2. A pipe 120 mm bore diameter carries water with a head of 3 m. The pipe descends 12 m in altitude and reduces to 80 mm bore diameter. The pressure head at this point is 13 m. The density is 1000 kg/m³. Assuming no losses, determine i. The velocity in the small pipe (7 m/s) ii. The volume flow rate. (35 dm³/s) 3. A horizontal nozzle reduces from 100 mm bore diameter at inlet to 50 mm at exit. It carries liquid of density 1000 kg/m³ at a rate of 0.05 m³/s. The pressure at the wide end is 500 kPa (gauge). Calculate the pressure at the narrow end neglecting friction (196 kPa) 4. A pipe carries oil of density 800…
1. A pipe 100 mm bore diameter carries oil of density 900 kg/m3 at a rate of 4 kg/s. The pipe reduces to 60 mm bore diameter and rises 120 m in altitude. The pressure at this point is atmospheric (zero gauge). Assuming no frictional losses, determine: i. The volume/s (4.44 dm³/s) ii. The velocity at each section (0.566 m/s and 1.57 m/s) iii. The pressure at the lower end. (1.06 MPa)
3. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a flow rate of 6 L/s. For satisfactory operation, the static pressure at the pump inlet must not be lower than 26 m of water gage. Determine the smallest standard commercial steel pipe that will give the required performance. 4.5 mm- Pump -Q = 6 L/s 90°- elbows 3.5 m Water 5°C
6. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a flow rate of 6 L s'. For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of the water gage. Determine the smallest standard commercial steel pipe that will give the required performance. pump 4.5 m. 1.8 19=d 3.5 m 7. water 90° elbow
Water is transported in a pipe, at an average flow rate of Q = 50 L/s. Calculate the pressure difference p between the 2 manometers. We can assume that the energy losses by friction are negligible, and that there are only singular energy losses (be careful to identify ALL the singularities). The pump adds an energy of HP = 10 m to the system. "GATE VALVE" P2 OUVERTURE COMPLÈTE do = 150 mm Q = 50 L/s • 2) 2 m Q = 50 L/s COUDES À POMPE RAYONS COURTS do = 150 mm (Hp = 10 m)
4. The system in Fig. consists of 1200 m (length) of 0.05 m (diameter) cast iron pipe, two 45° long-radius elbows, four 90° flanged long-radius elbows, and a fully open globe valve. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m³/s of water at 20°C into the reservoir? Average surface roughness of cast iron is ε = 0.26 mm. For water at 20°C, take density, p = 998 kg/m³; dynamic viscosity, μ = 0.001 Pa-s; and acceleration due to gravity, g = 9.81 m/s². 90° elbow: KL90, elbow K₁ = 0.5 ent Elevation (1 400 m = 0.3 45° elbow: KL45,elbow=0.2 Elevation 500 m ! Sharp exit Open KL = 10 globe valve Klexit = 1
A liquid (SG = 0.562) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -9 psi and 41 psi, respectively. The rate of flow in the pipe is 0.898 ft3/s. What will be the rating of the pump (in horsepower) if its efficiency is 90%? Neglect energy (friction) losses in the system. Use x = 5 ft., y = 9 ft. Use 1 hp = 550 lb-ft/s. Round off to two decimal places.
Water flows at the rate of 0.015 m/sec from open reservoir A to open reservoir B (both are large reservoirs that are open to the atmosphere) through two concrete (8 = 0.32 mm) pipes connected in series. If L1 = 800 m, Di = 16 cm, L2 = 200 m, and D2 = 8 cm, determine the difference in water surface elevations (Az) of the reservoirs. The coefficient of contraction (K.) is 0.36, the entrance coefficient is K = 0.5, the exit coefficient is K = 1.0, and assume fully turbulent flow (Xx = 9810 N/m?, Ku = 1.12 x 10-6 m²/s). You do not need to check if the assumption of fully turbulent flow is valid, just assume that it is valid. А Az =? Pipe 1 В Pipe 2 undefined
Q2: As shown in figure (2), when the pump develops (7.5m) of head, and the velocity of flow through the pipe No.3 is 2 m/sec. Neglecting the minor losses, find the flow in pipe No.1 and pipe No.2, and the elevation of pipe No.2 at discharge point. The pipe characteristics are as follows Pipe 1 2 3 (f) for all pipes = 0.03. EL.30m 4 Water ( P L(m) 1200 600 1200 D(mm) 600 600 600 EL.: ? Figure (2)
Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.
2.attention to the piping system shown in the figure below. Pipes 1, 2, and 3 are installed in parallel to connect reservoirs A and B. It is known that the discharge in the main pipe is 500 L/s. Determine Q1, Q2, and Q3! Use the data related to the piping system as listed below. • D1 = 350 mm, L1 = 300 mm, f1 = 0.014 • D2 = 450 mm, L2 = 200 mm, f1 = 0.0145 • D3 = 250 mm, L3 = 350 mm, f1 = 0.017 %3D A
A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -8 psi and 44 psi, respectively. The rate of flow in the pipe is 0.714 ft3/s. Neglect energy (friction) losses in the system. Use x = 4 ft., y = 7 ft. Use 1 hp = 550 lb-ft/s. Efficiency of the pump is 91%. What is the head in the pump (ft) ? Round off to two decimal places.