Problem 5 only, solve carefully, include the units in every step and draw the diagram. Thanks! A hollow shaft transmits 10 kW and running at 650 rpm with a shearing stress of 55 Mpa. The outside diameter is 1.2 times that of the inside diameter. Find the inside and outside diameters in mm.

Problem 5 only, solve carefully, include the units in every step and draw the diagram. Thanks! A hollow shaft transmits 10 kW and running at 650 rpm with a shearing stress of 55 Mpa. The outside diameter is 1.2 times that of the inside diameter. Find the inside and outside diameters in mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3- Draw Torque vs. angle oi twist for Cast Iron specimen
I have a 52100 steel hollow shaft, that will be threaded into a 1 inch thick plate of aluminum 7075. The shaft is 960 mm in length, 40 mm OD and 20 mm ID. The threaded end of the shaft is M30X3.5. What would be the recommended torque for the shaft, with the dissimilar metals. I’m expecting a range between 100-280 ft-lbs but can justify it.
Parvinbhai
A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required to tranmit a power of 60kW at a speed of 2950 rpm if the modulus of rigidity is 79.5GPa calculate the angle of twist in degrees
2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
B) A simply supported shaft is shown in the following Figure. A constant magnitude distributed unit load p is applied as the shaft rotates. The shaft is also subject to a steady torque of Tmax 2000-N -m., find the diameter of shaft required to obtain a safety factor of 2.5 in fatigue loading if the shaft is steel of Sut 814 MPa and Sy 703 MPa. The dimensions are in cm, the distributed force in N/cm, and the torque is in N-m. No stress concentrations are present, the shaft is machined, the required reliability is 90%, and the shaft operates at room temperature Figure: 1= 20-cm: b = 18-cm ; a = 16 cm Applied distributed load p:= 1000 N em ; 区区
In a two ram hydraulic steering gear the diameter of the rams is 280mm, diameter of the rudder stock is 350mm ...
Pls solve this, subject is machine design
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
A solid circular shaft of 35 mm diameter transmits a torque of 1460 Nm. The value of maximum shear stress is?
This course Lets consider a shaft having a diameter of 50 mm, subjected to the shown torques. Calculate the shear stress at point A. 800 N m 300 N-m Select one: 32.6 MPa 44.8 MPa O 29.36 MPa O 12.2 MPa O 20.37 MPa
Determine the maximum shear stress and maximum normal stress of the cantilever shafts in the figures below: 10 KN 200 Note: All dimensions in mm. 5 KN.m 20.0