Problem 5.3-21. The stress-strain diagram for a polyester resinis given in the figure. If the rigid beam is supported by astrut AB and post CD, both made from this material, andsubjected to a load of P = 80 kN, determine the angleof tilt of the beam when the load is applied. The diameter ofthe strut is 40 mm and the diameter of the post is 80 mm.2 mσ (MPa)100B95828580compression70605040--tension32.2200.5 m0.75 m 0.75 mD€ (mm/mm)00.01 0.02 0.03 0.04

Answered: Image /qna-images/answer/85822058-7cf1-4edb-9e98-303f194597e3.jpg

Answered: Problem 5 .3-21. The stress-strain…

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 49PQ

See similar textbooks

Similar questions

An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
Can compress stress be applied to a rubber band?
Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have, and specify where D must be located for a strut of this length to be used. Take x= 120 mm. 60 mm D. y 20 mm E The smallest length CD may have is mm. The coordinates of point Dare ( and Imm.
Referring to Fig. compute the maximum force P that can be applied by the machine operator, If the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 4000 psi and 5000 psi, respectively. The diameters are 0.25 inch for the pin, and 0.5 inch for the control rod. Assume single shear for the pin at B. Figure P-121 2 in 10 MATHno.com 6 in 2 in
The five-bolt connection must support an applied load of P = 3400 lb. If the average shear stress in the bolts must be limited to 43 ksi, determine the minimum bolt diameter that may be used for this connection. ooooo Answer: dmin in.
The five-bolt connection must support an applied load of P-4700 lb. If the average shear stress in the bolts must be limited to 43 ksi, determine the minimum bolt diameter that may be used for this connection. Cocoo Answer: dmin in.
A piece of steel wire, 200.0 cm long and having e cross-sectional area of 0.50 mm2, is stretched by a force of 50 N. Its new length is found to be 200.1 cm. Calculate the stress and strain, and the Young modulus of steel.
The five-bolt connection must support an applied load of P-4900 lb. If the average shear stress in the bolts must be limited to 46 ksi, determine the minimum bolt diameter that may be used for this connection. ooooo Answer: dmin eTextbook and Media Save for Later in.
The rigid beam AB is subjected to a varied force10kN and is supported by a steel rod of 17 mm diameter at A. The beam is connected at point A with a double shear connection shown with a bolt of 20 mm diameter and with member AC with50°. The support at B is considered pinned. Determine the shear stress in the bolt at point A. 10KN/m 50 Connection detail at A 3-
The pole in the figure is at a 90° bend in a power line and is therefore subjected to more shear force than ones in straight parts of the line. gw 30° 80° mm T The tension in each line is 3.80 × 104 N, at the angles shown. The pole is 15.0 m tall, has an 17.0 cm diameter, and can be considered to have half the strength of hardwood. 90° (a) Calculate the compression of the pole (in mm). 0.581 (b) Find how much it bends (in mm). 3.497 X mm
The beam is supported by a pin at A and a short link BC. Figure 1 of 1 > 0.5 m Tadika 1m 1.5 m 1.5 m H. Part A If P = 13 kN, determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as shown, and each has a diameter of 17 mm. (Figure 1) Enter your answers separated by commas. TA. TB. TC = Submit Provide Feedback 197| ΑΣΦ | 11 | vec Request Answer MPa I

SEE MORE QUESTIONS

Recommended textbooks for you

Physics for Scientists and Engineers: Foundations…

Physics

ISBN:

9781133939146

Author:

Katz, Debora M.

Publisher:

Cengage Learning

University Physics Volume 1

Physics

ISBN:

9781938168277

Author:

William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:

OpenStax - Rice University

Physics for Scientists and Engineers: Foundations…

Physics

ISBN:

9781133939146

Author:

Katz, Debora M.

Publisher:

Cengage Learning

University Physics Volume 1

Physics

ISBN:

9781938168277

Author:

William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:

OpenStax - Rice University

SEE MORE TEXTBOOKS