Problem 4 The shown bent tube is connected to a guide at A and rests on a roller support at B. It is subjected to the shown force and moment. Determine the reactions at A, and B. 15m 250 N 800 N 400 Nm 1.5 m 1 m 45 B

Q: Draw the frontside and topview the Shape Shown

A: Asked: To draw the front, side and top view of the given shape.   The required engineering id drawn…

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+1=5

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: Hi can you give me analysis about space truss?

A: This question is related to the Truss analysis from Structural analysis from Civil Engineering. This…

Q: What is the other name for air/cloth ratio?

A: The air to cloth ratio is defined as the total amount of air that is flowing through the filter of…

Q: 3 cm 7 cm 5 cm 5 cM Detenmine the Folloeing %3D

A: Calculation of area and moment of inertia

Q: How are forces between the tape and strips similar to those of magnetism?

A: The forces between a strip of adhesive tape and a surface are primarily due to intermolecular forces…

Q: What kinds of materials are used to construct space frames?

A: Space frames are the three-dimensional framework of struts and braces (as in buildings and sport…

Q: Determine external and total indeterminacy

A: Given data : Number of external support reaction (R)=2+1=3Number of member (m)=3Number of joint…

Q: What do beams develop?

A: Beams are the structural members which are loaded transversely. This transverse load can cause…

Q: ETERMINE THE LOCATION OF CENTROIDAL X AND Y. NOTE: UNITS ARE IN INCHES.

A:

Q: GENERAL INSTRUCTIONS: Answer the following questions comprehensively and neatly. FILE. - History of…

A: (1) Structural Analysis is not new as it has evolved over several thousand years. During early time…

Q: The T shaped cross section shown below is reinforced with 4 of 32 mm bars with fc'= 20.7 MPa and fy…

A:

Q: Define Vertical Stresses.

A: The total vertical stress acting at a point below the surface of the ground is due to the weight of…

Q: what is force in FG

A: Given data in question  Force 60 kips Span 16 m Height 15 m To find out  Member force in FG

Q: Define Allowable Stress Design

A: Their are mainly two type of design concept: Allowable stress method Load and resistance factor…

Q: 4. What is the total force on a damn that is an isosceles triangle with sides. of 35m? The dam is…

A:

Q: Define induced stresses ?

A: The internal resistance of a body to changes and deformation due to applied load is known as stress.…

Q: GENERAL INSTRUCTIONS: Answer the following questions comprehensively and neatly. FILE. History of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Can some beams be subjected to an axial force?

A: A beam is a straight horizontal member that supports loads which are concentrated, uniform and non…

Q: DETERMIME Fou つ こ I =

A:

Q: B) What is the difference between Spaced Sheeting and Close Sheeting

A: Solution: Closed sheeting is defined as the continuous frame having vertical and horizontal…

Q: Determine external indeterminacy

A: Given:- A frame is given with fixed support To determine:- The external indeterminacy

Q: what is grain elasticity?

A: Grit is the name for what is on a grinding, sanding or polishing tool. It is made up of a hard…

Q: Describe one of the methods of measuring surface tension with a physical justification.

A: Given :surface tension                                              To determine: method of…

Q: What is beam

A: The amount by which a beam deflects upon its cross-section, bending moment and shear force. For…

Q: Differentiate between elasticity and plasticity.

A: Elasticity:  Elasticity is the property of a material which regains it's original shape once the…

Q: Draw the front, Side and top

A: For this, we can draw the diagram in Autocad. I have used the same to draw the diagram and have…

Q: Define Steel Area

A: Answer Introduction Steel is the most important material used in the field of construction. Steel is…

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.