1. What is the surface texture in microinches is specified for the cylinder surface with a maximum material condition of 1.250"? Leave out the units, it is microinches, just type the number. * 2. How many dimensions are expressed using the limit method? 3. Is the sectional view a half or full section? 4. What revision is this part on? Thank yo

Q: What is the relationship between sensitivity and radius?

A: The change in angle or gradient of the level that results in movement of the bubble is known as…

Q: Understand how the various bonding agents cause adherence?

A: Bonding agents are the compounds that join two or more different materials by bonding their…

Q: Find the centroid of given composite figure. Set- up the reference axis on the lower left corner.…

A:

Q: Differentiate quartz and quartzite

A:

Q: What types of sculpture are commonly available?

A: Sculpture is a generally a form of artwork used in interior as well as exterior locations.

Q: Many objects, such as train tracks and road joints, are specifically designed to allow extra space…

A: Brief concept- Train tracks and road joints- Train tracks are the path for the trains over which…

Q: Define Dilatancy.

A: Dilatancy is the property of dense packed granular material in which the volume increases while…

Q: Given the following data, compute for the total excavation required for column footing/s. Write…

A: As per Bartleby's guidelines, we are supposed to answer only one question. Kindly repost other…

Q: Q4: Prove that:

A:

Q: ssed steel band acts as a line printer, creating the letters on the sheet of paper. Provide an…

A: The printing mechanism of a line printer is a metal band, or loop, of type characters is known as…

Q: What is LAP SPLICING? Illustrate a figure and explain it thoroughly

A: A lap is when two pieces of reinforcing bar (rebar) are overlapped to create a continuous line of…

Q: The T shaped cross section shown below is reinforced with 4 of 32 mm bars with fc'= 20.7 MPa and fy…

A:

Q: Question Bank- Centroids Jse the method of composite areas to calculate the centroidal coordinates…

A:

Q: What are the classes of hardboard?

A: Hardboard has high density and high strength, which is a quality substitute for wood and is commonly…

Q: A reservoir has the following inflows and outflows (in cubic meters) for the five months of the…

A: Storage at the beginning of the month of August =  80 m3.   Month August September  October…

Q: 250mm 250mm Reinforcing Bars

A: Given:-size-250mm x 250mmload =400kNallowable stress=8MPa for concrete and 150MPa for…

Q: Step 5 incomprehensiable

A: In the step 5Settlement can be calculated using as below

Q: B) What is the difference between Spaced Sheeting and Close Sheeting

A: Solution: Closed sheeting is defined as the continuous frame having vertical and horizontal…

Q: determine the degree of indeterminacy.

A: * Hinge support: - It is defined as the support which resists horizontal and vertical reaction but…

Q: what is grain elasticity?

A: Grit is the name for what is on a grinding, sanding or polishing tool. It is made up of a hard…

Q: What is Sloped Glazed.

A: Glazing: The installation of glass to the building components or interiors of the structure is…

Q: 20ド Sm 10m

A:

Q: Define Steel Area

A: Answer Introduction Steel is the most important material used in the field of construction. Steel is…

Q: Which tools that can be used to :1 draw the following shape in .AutoCAD Left-side view Top view…

A: Answer: 4. Construction Lines, Offset, Line, Trim, Layers

Q: Consider the beam X-section shown. Assume 1 inch clear spacing between two layers of bars. As the…

A: 1 inch clear spacing spacing between two layers of bars. Beam width = 12 inch Layer = 2 No of bars =…

Q: y 50 -30- 40 15 Dimensions in mm Fig. P8.15

A:

Q: 32 in 5 in. Cross section C |+6 in. 6 in.

A:

Q: With examples, describe what marble is and what it is most commonly used for.

A: When limestone is exposed to intense pressure or heat, marble is created. Marble, which is made of…

Q: Write the full form and define i) CRMB ii) PMB

A: TO Define.  CRMB  PMB

Q: What is the total length of extra bars at the midspan as shown below, 500 mm 500 mm 500mm 100 mm…

A: Please find the answer in the below attachments

Q: Find the moment of inertia (Ix, mm“) of the composite shape from the bottom base. Type answer in two…

A:

Q: PROBLEM 2: Determine the centroidal coordinates ( x-bar and y-bar) of the composite area shown in…

A:

Q: 10- What is the BOM and how is it arranged on a format?

A: We need to define BOM and how is it arranged on format Note : Since you have asked multiple…

Q: Give at least 5 examples of jobs where sealant and adhesive can be applied or used.

A: Sealants and adhesives are so confusing at an area of DIY. Some adhesives will seal and some…

Q: Draw any seven steel structure's shapes, also mention its aporopriate names.

A:

Q: where is the cross section solutions?

A:

Q: USE THE METHOD OF COMPOSITE AREAS TO CALCULATE THE CENTROIDAL COORDINATES OF THE PLANE REGIONS…

A: Here in this question we have to determine the value of centroid of the given shape. We have to…

Q: Define shrinkage limit.

A:

Q: PROBLEM 6: Determine the centroidal coordinates ( x-bar and y-bar) of the composite lines shown in…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.