Problem 4 The circuit shown below is operating in the sinusoidal steady state. a) Draw the circuit in frequency domain. b) Use any method to calculate the current i, in phasor mode (i.e. frequency domain), c) Write the current i, in steady state (i.e. time domain). 5 cos(2r + 10°) A 4 H 10 cos(21 - 60°) V

Problem 4 The circuit shown below is operating in the sinusoidal steady state. a) Draw the circuit in frequency domain. b) Use any method to calculate the current i, in phasor mode (i.e. frequency domain), c) Write the current i, in steady state (i.e. time domain). 5 cos(2r + 10°) A 4 H 10 cos(21 - 60°) V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

1. What is the shortest time required for a 4.3-krad/s sinusoid to increase from two-fifths to four-fifths of its peak value ? CHOICES: A. 120 s B. 140 s C. 160 s D. 180 s E. NOTA
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 0.2ms/cm and the volt/cm switch is on 1 V/cm. a) the frequency will be Hz b) the r.m.s value will be In CRO the beam can also be shifted vertically by applving a suitable DC voltage to the
For a series RLC circuit with a sinusoidal input voltage, the amplitude of the current passing through the circuit (I, in mA) is plotted as a function of frequency for two cases: Curve 1 with R1, L1. and Curve 2 with R2. L2 as shown in the next figure. The value of the capacitor used in the circuits is C=0.01 micro Farads. If the value of R2 =1600 Ohm then the input voltage (in volts) is: 7.5 25 110 Frequency H2 O a. 4 O b. 16 sin(9888 t) O c. 8 O d. 8 cos(6.28 f t) O e. 8 sin (6.28 R t)
Using a line phasor (circle), draw the two given phasors. Use the sine function as the base function.
Given a capacitive load absorbing 5 kW with a power factor of 0.85. The source connected to this load is an AC voltage supply with 120V RMS at a frequency of 50 Hz. Please find; A) Peak current (m) and RMS Current (ms) Values B) Draw peak voltage and current phasors on phasor diagram with everything labelled C) Find the value of an inductor that when connected in parallel will improve the power factor to 0.95.
Instruction: Provide the correct answer. 1. What is the relationship between the supply voltage and circuit current in purely capacitive circuits? 2. Vm = 100cos(377t + 75°) transform into sine form is a complex number that represents the amplitude and phase of a sinusoid. 3. 4. What is the phase relationship between a supply voltage and current through a purely inductive circuit? . 5. The rms value of the signal is also called the
1. Instruction: Provide the correct answer. 1. What is the relationship between the supply voltage and circuit current in purely capacitive circuits?. 2. Vm = 100cos(377t + 75°) transform into sine form is a complex number that represents the amplitude and phase of a sinusoid. 3. 4. What is the phase relationship between a supply voltage and current through a purely inductive circuit?. 5. The rms value of the signal is also called the 6. The It is also the cosine of the angle of the load impedance. 7. When Q < 0, the power factor is 8. The process of increasing the power factor without altering the voltage or current to the original load is known as 9. is the cosine of the phase difference between voltage and current. is the measurement to measure average power. 10. What is the meaning of VAR?
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
A source provides a sinusoidal current is (t) of 60 Hz to two resistors and a capacitor, so that a current ic (t) flows through this last element. a) Indicate under which conditions ic (t) would be late with respect to is (t), under which conditions it would be in phase and under which conditions it would be earlyb) If C increased and the rest of the circuit remained the same, indicate whether the effective value of ic (t) would increase or decrease
In the circuit, v₁ and ₂ are AC sources with = 100 rad/s. The phasor diagram shows the phasors of v₁ and v₂. It is not drawn to scale. You may assume the system is in steady state. V3 is a DC source. (a) What is v₂ where I is the period of the waveform ? (b) What is the waveform ia(t)? (c) What is the maximum value of the waveform va(t)? V3 L + V1 1 + + Va V2 V₂ a Im V₁ να Re |V1|: |V2|: alpha: V3: C: L: 2 V 3 V 30 degrees 3 V 10 mF 25 mH
a) Draw a sinusoidal waveform on a graph paper , assuming that Vx (effective value) and fx (kHz) are frequency. Vx= 3Volt, fx= 5Hz, Rx= 1000 *Draw the Time / div and Volt / div switches to show their positions in the screenshot where this waveform is formed and write down these locations. *Show the accuracy of the screenshot by making the necessary calculations. b) Draw a square waveform on graph paper, assuming that Vx (peak value) and fx (Hz). Vx= 3Volt , fx= 5Hz , Rx= 1000 *Draw the Time / div and Volt / div switches to show their positions in the screenshot where this waveform is formed and write down these locations. *Show the accuracy of the screenshot by making the necessary calculations. Example: Time/ Div and Volt/ Div button ms 1 5 2 16o 2 5 10 5 2 20 10 2 50 20 2 50 20 2 10 mV 10 20 CAL 5.
1. What effect does changing the frequency on the effective value of sinusoidal voltage? 2. What effect does changing the amplitude on the effective value of sinusoidal voltage?