Answered: Problem #4: For the circuit shown below…

Problem #4: For the circuit shown below determine the average power delivered to R1 and R2, if the current waveform has the following shape. Ri342 R362 A 2 2. 3 나

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Related questions

Q: Q3) a) What is the reading of each wattmeter if ZA = 10 430°, ZB = 30 20°, Zc = 20 L- 30° b) Show…

A: What is reading of the wattmeters Two wattmeter method used to measure to power across the load. In…

Q: For the system with v(t) = 120 sin(2wt - 30)V and i(t) = -12 cost(2wt + 70)A. Determine average…

A: Average power of a single phase circuit is P = V I cos φ Where V is the magnitude of the voltage…

Q: A three phase wye connected alternator has synchronous impedance of 0.7 + j7.0 ohms per phase with…

A: The solution is given below

Q: Problem 8: Calculate the apparent power, power factor, real power and reactive power associated with…

Q: The percent impedance of a 115 kV transmission line is (3.8 + j 15.1) % at 100 MVA base. What is its…

A: Basic problem on power system analysis.. Look below for the solution..

Q: 3. Using nodal analysis, determine the current through the 2+j5 ohms impedance. 1 jsn 2

Q: The maximum instantaneous voltage and current output of an alternator are 300 V and 20 A,…

A: r

Q: A source supplies power to the following three loads connected in par- allel: (1) a lighting load…

A: The solution is given below

Q: 8 Ω -j2 N () 4/0 Α Ν

Q: Question 1 A 220 -v three phase motor takes 21.437 W at 0.71 lagging power factor. what us the line…

A: Given a 3-phase motor with, Power rating, P = 21.437 W Voltage, VL=220 V rms Power factor, cosφ=0.71…

Q: Two wattmeters used to measure the power input in a 3.phase circuit indicate 1000 W and 500 W…

Q: An Alternator has an effective line voltages of 1 20 V, has an impedances of 5 / 45 in Wye…

Q: A load connected in star has an impedance of 300 + J 400 Ω per phase. The load is 400 v, 50 Hz,…

Q: all V R sine sine Let the voltage source be 202135, the current source be 10245 and the impedance of…

A: In this question, We need to determine the value of resistance R if angle of current flow in this…

Q: 452 2. 34j2 Zea Find the equivalent impedance

Q: Problem 4 Find the average power loss and power factor for each of the circuits whose input voltage…

A: we need to answer average power loss and power factor and also have to find if it is leading or…

Q: 10.17 A load of 300 kW, with power factor 0.65 lagging, has the power factor improved to 0.90…

A: Real power of load, PL = 300 kW. Power factor of load = 0.65 Reactive power is given as,

Q: Sweep generator In three phase power measurement using one watt-meter method, if the load is…

A: In this we will write about power measurements using one wattmeter method....

Q: The values of the elements for the given circuit are given below. The maximum average power that can…

A: The given circuit is shown below. We need to calculate the maximum power transferred to the load…

Q: From the circuit, determine the value of load z for maximum power transfer and the maximum average…

Q: 53. A balanced wye-connected load of 30 + j10 ohms per phase is connected to a 3-phase 60 HZ 208…

A: Given Balanced wye connected load Load impedance per phase ZL=30+j10 ΩFrequency f=60 Hz voltage…

Q: There is a system including 4 buses according following Figure, calculate the admittance matrix for…

Q: Two alternators A and B delivers 100 and 150 A, respectively to a load. If these currents are out of…

Q: (A V E, V

A: The solution is given below

Q: Image 1: What is the complex power delivered to the load? Image 2: What is the average power…

Q: Please answer the following: 1. A balanced star connected load has an impedance of 6 + j8 ohms per…

Q: 9. A three-phase overhead transmission line is being supported by three-disc suspension insulators;…

Q: Two alternators A and B deliver 100 and 150 A, respectively to a load. If these current are out pf…

A: Given data, Current flowing through both the alternates are, I1=100 A, I2=150 A Angle between both…

Q: If a power system has 10,000 kVA capacity, operating at 0.7 lagging power factor Determine the…

A: Explanation: The required reactive power to improve the power factor from 0.7 to 0.85 is QC = P…

Q: 12 2 V V 310

Q: Modify Figure shown by adding a 1.5 resistance to each of the two outer lines, and a 2.5 resistance…

Q: 2 that absorbs the naximum average power. Calculate that maximum average power. -J4 2 j10n 2/0 A Z.

Q: An overhead single phase short transmission line delivers 4000 kW at 20kV at 0.8 pf lagging.…

Q: Determine the average power delivered to each of the boxed impedances in the circuit below if V, =…

A: Power in AC circuits has two components. Here, S is called apparent power (in VA’s), P is termed as…

Q: For the given circuit calculate the maximum power that can be transferred from the circuit to the…

A: In the given circuit, Find the maximum power transfer to the load impedance ZL For maximum power…

Q: (ii) Two wattmeters are connected to measure power input to a three phase balanced circuit indicate…

Q: Vs = 11720 V; RL = 50 2; jXL = j86.7 2. Calculate the complex power and correct the power factor to…

Q: A single phase transmission line is transmitting power to a load of 1,100 KW at 11 KV and at unity…

A: Given that A single phase transmission line is Input power p=1100kw Voltage v=11k Power factor…

Q: Three-phase, 50 Hz, 132 KV power system of equivalent impedance 10+j35 12 with load 110+j29 12.…

Q: The average total power in a triphasic sytem that powers a connected balanced wye load is 12 kW with…

A: we need to calculate the line current (IL).

Q: 80 -j2 n 4<0° A -j3 0 50 j20 10<30° V

Q: 5. Three impedances of (1+j5)N, (1+j12)N and (2+j3)N are connected in star to a 3-0 system with line…

Q: • What is the phase sequence of the following voltages? v,(1) = 137 cos (@t +63°)y a V, (1) = 137…

A: for the given phase voltages Va(t) = 137 cos (wt+63) V Vb(t) = 137 cos (wt-57) V Vc(t) = 137 cos…

Q: Question 4: Determine the average power delivered and Power factor to network having the following…

Q: The voltage across and the current through a load are expressed as follows v(t) = -170 sin 377t V…

A: The voltage is expressed as:

Q: 16. Find the value of impedance which absorbs a complex power of 2300 VA with a 30 degrees angle at…

Q: A- For the network shown, calculate the total power delivered to the circuit. 202 20 L Tjtose 240n…

Q: In a balanced star connected 3-phase circuit, of impedance (15+j20) ohm is connected to a 440V,50HZ…

A: Given data,

Q: 11.) A single phase inductive load at 0.70 power factor lagging takes 32 kVA power. Compute the…

A: The solution is given below

Concept explainers

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors. The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.

Question

100%

Please help explain, thank you!!

Problem #4: For the circuit shown below determine the average power delivered to R1 and R2,
if the current waveform has the following shape.
A
2
2.
3
나

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2/ Find Yous for the power system all reactance on a common base. Bus 3 j0.25 j0.10 j0.25 Bus 2 j0.125 Bus 1 j0.40 j0.20 j0.10 Bus 4
A curve is drawm in descending order of load with time. Al1
Referring to the Figure 2, compute the following values, given that the operating frequency is 60Hz and the voltage is 120V: (a) The inductive reactance (b) Source current (c) Apparent power, active power and reactive power Sketch and illustrate the power triangle with proper labelling, units and values. E 160 150 mH Figure 2
A power supply A delivers 10 V dc with a ripple of 0.5 V r.m.s. while the power supply B delivers 25 V dc with a ripple of 1 mV r.m.s. Which is better power supply ?
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
The values of the elements for the given circuit are given below.What is the maximum average power that can be transferred to the ZL load?R1 = 400 OhmsL = 500j OhmsR2 = 100 Ohms
a) Determine a corrent denote I1 b) Determine the voltage V0 c) Determine complex power supplied by source
Lightning over-voltages and switching phenomena of switchgears are two examples of transient voltages occur at transmission lines or distribution systems. Based on Figure 2 (b), identify whether the waveform is lightning or switching signal. Support your answer. 1.5 0.5 20 40 60 80 100 Time (us) Voltage (p.u.)
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1
Short term and long term effects of wind energy on power system
a) why is there a wattmeter reading when the load is purely inductiveb) why is there no wattmeter reading when the load is purely capacitive
For figure 3, how do I find: Is The average power delivered to each element, the reactive power for each element, & the apparent power for each element. Find PT, QT, ST, and Fp for the system. Sketch the power triangle.