Problem 317 A hollow bronze shaft of 3 in. outer diameter and 2 in. inner diameter is slipped over a solid steel shaft 2 in. in diameter and of the same length as the hollow shaft. The two shafts are then fastened rigidly together at their ends. For bronze, G 6 x 10 psi, and for steel, G 12 x 10 psi. What torque can be applied to the composite shaft without exceeding a shearing stress of 8000 psi in the bronze or 12 ksi in the steel? Hollow Bronze D = 3 in, d = 2 in Steel Core D= 2 in

Problem 317 A hollow bronze shaft of 3 in. outer diameter and 2 in. inner diameter is slipped over a solid steel shaft 2 in. in diameter and of the same length as the hollow shaft. The two shafts are then fastened rigidly together at their ends. For bronze, G 6 x 10 psi, and for steel, G 12 x 10 psi. What torque can be applied to the composite shaft without exceeding a shearing stress of 8000 psi in the bronze or 12 ksi in the steel? Hollow Bronze D = 3 in, d = 2 in Steel Core D= 2 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a hallow shaft (Diameter and length) that develops 80 kN of power while rotating at a speed of 4000 rpm. The design constrains are as under: The angle of twist not to exceed 0.200 Shear stress is not to exceed 480 MN/m? The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m?.
Design a rigid flange coupling to transmit a torque of 228N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa > Provide FBD
Two designs for a shaft are being considered. Both have an outside diameter of 50 mm and are 600 mm long. Oneis solid but the other is hollow with an inside diameter of 40 mm. Both are made from steel. Compare the torsionalshear stress, the angle of twist, and the mass of the two designs if they are subjected to a torque of 850 N ·m.
Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Answer in Word please
A motor driving a solid circular steel shaftwith diameter d = 1.5 in. transmits 50 hp to a gear atB. The allowable shear stress in the steel is 6000 psi.Calculate the required speed of rotation (number ofrevolutions per minute) so that the shear stress in theshaft does not exceed the allowable limit.
Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m
2. A composite shaft is made of slipping a bronze tube of 3-in. outer diameter and 2-in. inner diameter over a solid steel shaft of the same length and 2-in. diameter. The two components are fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 10 ksi for bronze and 14 ksi for the steel? If the hollow tube is made out of steel and the solid shaft is made out of bronze, what is the largest torque that can be carried by the composite shaft if the same working shear stresses are applied? For bronze, G = 6 x 10° psi, and for steel, G = 12 x 10°.
PROBLEM 2. The turbine in the figure generates 90 kW power. 50 kW of power is drawn from the gear at C and 40 kW from the gear at D. Revolution speed of A-36 steel shaft is 600 RPM. If F.S. is 1.5 according to the shear yield stress and the allowable angle of twist of E with respect to B is 0.2 degrees, calculate the required shaft diameter as a multiple of mm. The shaft can rotate freely at bearing at E.
Design a hollow circular steel shaft to transmit an applied torque of 360,000 in-lbs. Theallowable shear stress is 6,000 psi and the inside diameter is to be 0.6 times the outsidediameter.
Problem Set 3 1. The solid aluminum shaft ABCD carries the three torques shown. (a) Determine the smallest safe diameter of the shaft if the allowable shear stress is 15 ksi. (b) Compute the angle of rotation of end A of the shaft usingG = 4 x 106 psi. 1600 lb · in. 2400 lb · in. 4000 lb · in. 36 in.
PROBLEM 2. The turbine in the figure generates 90 kW power. 50 kW of power is drawn from the gear at Cand 40 kW from the gear at D. Revolution speed of A-36 steel shaft is 600 RPM. If F.S. is 1.5 according to the shear yield stress and the allowable angle of twist of E with respect to B is 0.2 degrees, calculate the required shaft diameter as a multiple of mm. The shaft can rotate freely at bearing at E. 2 m 4 m E 1 m
Q/A shaft supported at the ends in ball bearings carries a straight tooth spur gear at its mid span and is to transmit 7.5 kW at 300 r.p.m. The pitch circle diameter of the gear is 150 mm. The distances between the centre line of bearings and gear are 100 mm each. If the shaft is made of steel and the allowable shear stress is 45 MPa, determine the diameter of the shaft. Show in a sketch how the gear will be mounted on the shaft; also indicate the ends where the bearings will be mounted? The pressure angle of the gear may be taken as 20°.