PROBLEM 3. The beam has a thin-walled cross section as shown 21 mm 35 mm 21 mm and the wall thickness is 4 mm. For a vertical shear of 5000 N, (a) determine and sketch shear flow distribution (b) determine the maximum shear stress in the beam. 28 mm 75 mm

PROBLEM 3. The beam has a thin-walled cross section as shown 21 mm 35 mm 21 mm and the wall thickness is 4 mm. For a vertical shear of 5000 N, (a) determine and sketch shear flow distribution (b) determine the maximum shear stress in the beam. 28 mm 75 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: area of the steel reinforcement in tension side (As)

A: To provide the definition of area of the steel reinforcement in tension side (As) and the tensile st...

Q: 4. An igloo or Eskimo hut is built in the form of a hemispherical shell with an inside diameter of 1...

A: Given Data- Hemispherical shell igloo/eskimoInside diameter=12 ftuniform thickness=2 ftweight=40 lb ...

Q: Problem 3: A bracket of negligible weight shown in the figure below is loaded a force of 13.34 kN. F...

Q: *Prob. 1.4-14. Beam AD is supported by a rollers at B and C that are equidistant form the ends, as s...

Q: From the Figure, determine the minimum length of the curve. Assume a=11.2 ft/sec and perception-reac...

Q: By the conditions of the will, the sum of $35,000 is left to a 12 year old girl to be held in a trus...

Q: E oth ends of the steel shaft are attached to rigid supports. Find the distance a where the torque T...

Q: 7. A cantilever beam with a rectangular section has a longitudinal hole drilled throughout its lengt...

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy...

A: Given data, P = 60 kN E of aluminium = 73 GPa Aluminum rod diameter = 16 mm Aluminum rod length (L...

Q: 4. From the given shear diagram below, where is the point of inflection located from the right end i...

A: In shear force diagram point of inflection is where the sign of the shear force in shear force diagr...

Q: Question 2: (50 marks) The v-t graph shown. Find the distance traveled for the time 0 to (1500+N) se...

Q: A two-storey apartment building designed by Engr. Sang Woo has a brace system of main structural mem...

Q: 4. A steel cylinder surrounded by a copper tube is subjected to a compression between parallel plate...

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

Q: A brass rod is 185 cm long and 1.6 cm in diameter. What force in kN must be applied to each end of t...

A: What force in kN must be applied to each end of the rod to prevent it from contraction

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

A: Given data, Height (H1) = 200 ft Height (H2) = 50 ft Horizontal length (L) = 2000 ft Head loss due ...

Q: Sketch the shear and moment diagram for the beam loaded shown. 6kN/m 10kN 4kN/m losm 1.5h In <庭

Q: For the figure shown, determine the stresses of the wires and the elongation when the temperature ch...

A: Given data in question Loading in the form of UVL Span member length Area Elasticity modulus Coeff...

Q: A Machine was purchased on 1st January 2004 at a cost, of P58,000 and the cost of installation Rs 8 ...

A: Expected working life of machine=100,000 hours Cost of machine (Rs 50000+8000)=Rs 58,000 Scrap value...

Q: From a reservoir A whose surface elevation is 225 m, water is pumped through 1200 m. of 300 mmø pipe...

A: Given data Diameter of pipe(d) = 300mm = 0.3m Length of pipe between 1 and 3 = 600m Length of pipe b...

Q: Include FBD.

A: The given truss is a simply supported K-truss. The magnitude and the type of force are to found for ...

Q: 1- Top View 2- Front View 3- Side View Dimensions are shown in mm. 50 42 20 20 20 80 85- 81 02

Q: The beam is supported by a roller at B and a pin at C and is subjected to the distributed load shown...

A: Given data:

Q: Solve the bending stress about points A and B

A: #calculation of bending stress at point a A, B##

Q: A cantilever beam with a rectangular section has a longitudinal hole drilled throughout its length. ...

Q: Determine the centroid of the composite area shown in Fig.Q2.

A: The centroid of the composite area shown in Fig Q2 has to be determined

Q: As a ship is approaching the dock at 45.0 cm/s, an important piece of landing equipment needs to be ...

A: The values given in the question are as follows: Speed of ship(u)=45 cm/sec or 0.45 m/sec Speed of e...

Q: Compute the neutral axis of the beam. Compute the value of the total compressive force of concrete. ...

Q: *7-32.d The double T-beam is fabricated by welding the three plates together as shown. Determine the...

A: Given: A double beam, Shear force = 80kN Find: Shear stress = ?

Q: Determine the mass of the heaviest uniform cylinder that can be supported in the position shown with...

Q: A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z ...

Q: Create an LOWER TRIANGULAR MATRIX using ROW operations. Show each step and the formulas used. Then, ...

Q: Problem 2. Investigate the adequacy of a 250mmx 250mm column, 3m high between lateral supports carry...

Q: Yu = 10 k N/m? J = 14 kN/u² clay Osat = 15,5 kN/ms Diagram 2 GWL -2.00 r = 16 kN/m³ sand I sut = 17K...

A: Total stress = Y*h Pore pressure=Yw*h Effective stress = total stress-pore pressure

Q: Solve the bending stress about points A and B

Q: 2) Mr. X performs the laboratory test and determines that 12 mg/l of alum dose is required to treat ...

A: Step 1: Amount of alum required per day = 14x10^6 x 12 /1000x10000= 168 kg

Q: A system of forces which produces zero moment:

Q: The perpendicular distance between the parallel tangents of a reversed curve is 35 m. The azimuth fr...

A: Reverse Curve: A curve that consists of two simple curves which are joined together and curving in o...

Q: A passenger ferry makes trips from a town to an island community that is 7 km downshore from the tow...

Q: Calculate the moment (positive if counterclockwise, negative if clockwise) of the 370-N force on the...

Q: how is Diastrophism related to Civil Engineering?

Q: Assume you are an observer standing at a point along a three-lane roadway. AlIl vehicles in lane 1 a...

Q: Calculate the moment (positive if counterclockwise, negative if clockwise) of the 370-N force on the...

A: Given data, Force = 370 N Theta (Θ) = 27° To find out the moment.

Q: uble the garden area with the addition of this path. How wide should the path be? ct one: .1m . 2.85...

Q: 3. A rigid beam AB rests on the two short posts shown. AC is made of steel and has a diameter of 20 ...

Q: From the given shear diagram below, where is the point of inflection located from the right end in m...

A: The shear force diagram given in the question are as follows:

Q: If tan A = 12/5 and sin A is negative, find cos A?

A: Given: tanA = 12/5 and sinA is negative Find: CosA

Q: Water flows steadily through the two relatively large tanks A and B as shown in Fig.1. The diameter ...

A: Using Torcellis equation for efflux. The discharge can be calculated. Then using conservation of mas...

Q: Chapter 2, Problem 2/088 An exhaust system for a pickup truck is shown in the figure. The weights Wa...

A: To Determine Forces in the hangers at points B, C, and D so that the force couple system at point O ...

Q: 25 kN w A В Using any method shown in class, determine the shear force and bending moment diagram fo...

Concept explainers

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.

Question

PRORLEM 3.
The beam has a thin-walled cross section as shown
21 mm 35 mm 21 mm
and the wall thickness is 4 mm.
For a vertical shear of 5000 N, (a) determine and
sketch shear flow distribution (b) determine the
maximum shear stress in the beam.
28 mm
75 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Shear stress distribution

VIEW

Step 3: Maximum shear stress

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. Determine the shearing stress in each of the four walls of a portion of a structural aluminum tubing when it is subjected to a torque of 3 kN-m assuming a uniform wall thickness of 4mm. A ( 51 ) mm В 100 mm 100 mm C D ( 51 ) mm
The d-14-mm-diameter solid rod passes through a D- 19-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a- 28 mm, and the head has a thickness of t- 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 105 MPa, and the bearing stress between the rod head and the support plate cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure. Support Plate Hole diameter D Rod Неad Answer in kN with 2 decimal places
SIMPLE STRESSES 340 mm Two plates are connected by bolts as shown in the figure. Compute the maximum axial stress that each plate will handle. The allowable shear stress of each bolt is 50 MPa and the diameter of each bolt is 20 mm. F F 150 mm 册 F 50 mm 340 mm
Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A on the cross section of the pipe. at section a-a. mun 40 mm 300 mm 300 mm
Q3) The aluminum tube shown in Figure (2) has a thickness of (5 mm) and outer cross sectional dimensions is ( 150 mm x 100 mm). Determine the maximum average shear stress in the tube. If the tube has length of (5 m), determine the angle of twist at point A KRS Figure (2) H
Determine the shear stress in pin A (double shear) and the normal stress in DE. The diameter of pin A is 0.125" and the cross section of DE is 0.15"x0.25". -2 ft -2 ft C A E 3 ft 600 lb
Required information Two solid cylindrical rods AB and BC are welded together at Band loaded as shown. Given: P=7 kips. A 30 in. -1.25 in. В 12 kips 25 in. 0.75 in. Find the average normal stress at the midsection of rod BC. The average normal stress at the midsection of rod BC is ksi.
A vertical force of P = 1000 N is applied to the bell crank shown. Determine: a) The required diameter of rod CD if the allowable normal stress is 50 MPa. b) The average shear stress developed in the 6-mm diameter pin B that is subjected to double shear. -450 mm B 45% 300 mm
L00% Given the thin-walled cross-section in figure 3 (dimensions in mm) with thickness equal to 1 mm, determine: 3. The maximum shear force T applicable considering that ơadm = 255 MPa (steel); 18 18
What are appropriate relations established from the calculation of maximum shear stress in a thin circular tube? 4 (b) t = (a) Tmax Tavg 3 'avg max 3 4 S Rỉ + R2R1+ R3 (c) Tmax when (R, = = 2avg - R.) (d) Tmax 3 A Rỉ + R? Here, (R, > R1) and S is shear force at the cross sectional and A is cross sectional area.
A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
Q1. ( The solid 100-mm-diameter steel cantilever shaft shown in Fig. 1 is subjected to an axial compressive force P = 200 kN and a torque T = 30 kN m. For point A on the outside surface of the shaft, determine:(a) The state of stress at point A. (b) The principal stresses and the maximum shear stress at the point; (c) The steel yield stress dyp = 350 MPa, determine the factor of safety for Point A if the maximum shear stress theory is used. Fig.1