Two blocks are supported by a pulley along an incline as shown. The lower block B has a weight of 37 lbs and the higher block A has a weight of 22 lbs. Assume that there is friction between the blocks with fls = 0.14 and assume friction between block B and the incline is also , = 0.14. Determine the angle z for which motion is impending. 27th 3716 AB А Tension in block A as a function of a can be written as TA Tension in block B as a function of a can be written as TB Thus, impending motion is at z = degrees.

Two blocks are supported by a pulley along an incline as shown. The lower block B has a weight of 37 lbs and the higher block A has a weight of 22 lbs. Assume that there is friction between the blocks with fls = 0.14 and assume friction between block B and the incline is also , = 0.14. Determine the angle z for which motion is impending. 27th 3716 AB А Tension in block A as a function of a can be written as TA Tension in block B as a function of a can be written as TB Thus, impending motion is at z = degrees.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

THE COEFFICIENT OF STATIC FRICTION BETWEEN THE BLOCK AND THE PLANE IS µs = 0.2. DETERMINE THE MAXIMUM VALUE OF WEIGHT W VWITHOUT CAUSING THE 50-LB BLOCK TO SLIP. D W 45°
1 F B •G DO d d UBC Engineering A group of engineering peasants have constructed a stationary battering ram in attempts to siege the castle of Santa Ono. Determine the tension developed in the linkages AB and CD as well as the angular acceleration if the 250 kg log is subject to a horizontal force of F 300 N and both linkages have an rad Assume the mass of the linkages are negligible. S angular velocity of w = 3 1.1 m and are an equal distance d : Links AB and CD have a length l gravity of the log. = 1.1 m away from the center of rad a AB rad aCD s2 ТАВ kN TCD kN A ||
Calculate the horizontal force P on the light 12° wedge necessary to initiate movement of the 30-kg cylinder. The coefficient of static friction for both pairs of contacting surfaces is 0.30. Also determine the friction force FB at point B. (Caution: Check carefully your assumption of where slipping occurs.) P Answers: P = FB = i i 30 kg B N N A
7.51 The two 200-lb blocks are pushed apart by the 15◦ wedge of negligible weight. The angle of static friction is 12◦ at all contact surfaces. Determine the the force P required to start the blocks moving.
3. he box is stationary on the inclined surface. The coefficient of static friction between the box and the surface is µs. (a)lf the mass of the box is 10 kg, a = 20°, ß = 30°, and µs = %3D 0.24, what force T is necessary to start the box sliding up the surface? (b)Show that the force T necessary to start the box sliding up the surface is a minimum when tan B = µs. T
Situation 1: The 300-1b force is to be resolved into components along lines a-a' and b-b'. P 300 lb b 60⁰ a' 1. Determine the angle a knowing that the component along line a-a' is 240-lb. 2. What is the corresponding value of the component along b-b'?
A solid steel shaft is transmitting 250hp at 1500 rpm a.) what should be its diameter if the deflection is not to exceed 1° for a length of 6 ft b.) what would be its ultimate stress if the factor of safety is 6? c.) if the shaft is hollow determine the dimensions of outside and inside diameters if (D=2d). d.) Compute the torsional deflection of the hollow shaft and determine which shaft is more rigid?
If the 20-kg smooth collar starts from rest at A, determine its velocity when it reaches point B. Neglect the size of the pulley. Take a = 350 mm, b = 250 mm, 0 = 35° and the constant force F = 350N b b a F
Question Bank - Friction The 40-N spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the 130 270 mm 192 mm wire.
The 40 kg block is placed on a 30° inclined and released from rest. The coefficient of static friction between the block and the inclined plane is 0.30. A) Determine the maximum value of the initial tension T in the spring for which the block will not slip when released. B) Determine the minimum value of the initial tension T in the spring for which the block will not slip when released. C) Determine the friction force on the block if T = 150 N.
Solve all support reactions using the SLOPE-DEFLECTION METHOD. 210 kN A 8 m- I B 40 kN/m 8 m -21 E = constant D 4m-4m- C HOD OF SOAP $4411
A horizontal shelf AD of length L = 600 mm, width b = 200 mm, and thickness t = 12 mm is supported by brackets at B and C [see part (a) of the figure]. The brackets are adjustable and may be placed in any desired positions between the ends of the shelf. A uniform load of intensity q. which includes the weight of the shelf itself, acts on the shelf [see part (b) of the figure]. A L (a) D L (b) Determine the maximum permissible value of the load if the allowable bending stress in the shelf is Oallow = 6 MPa and the position of the supports is adjusted for maximum load-carrying capacity. Round to two decimal places. Imax kN/m