Problem 3: The wrench shown in the figure below is used to tighten a bolt at A. If the wrench does not rotate when the load is applied to the handle, determine: a. The moment applied to the bolt b. The resultant force magnitude and orientation of the wrench on the bolt (e.g. the reaction force) 300 mm 400 mm 60

Problem 3: The wrench shown in the figure below is used to tighten a bolt at A. If the wrench does not rotate when the load is applied to the handle, determine: a. The moment applied to the bolt b. The resultant force magnitude and orientation of the wrench on the bolt (e.g. the reaction force) 300 mm 400 mm 60

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

Example An experimental device imparts a force of magni- tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the 900 mm 700 mm F moments of the force F about point O and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment. 300 mm 3050 mm Example The 30-N force P is applied perpendicular to the portion BC of the bent bar. Determine the moment of P about point B and about point A. P = 30 N C 1.6 m 45° B 1.6 m
6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C from the board. Determine the magnitude of the moment about B exerted by the 100 lb vertical force. Draw a free body diagram for the system. Then, use what you know about moments to solve for Mp What is the magnitude of the moment at point B due to P if P = 100 lb and 9 = 10"? Round to the nearest whole number. Enter a response then click Submit below lb in
a. Draw the reaction forces for the rod connected by a pin to the collar on a smooth rod (2D): X b. Draw the reaction forces for the single smooth pin joint (3D). Note: if you print this sheet, you may also cross out any force(s) or moment(s) in the adjacent diagram instead of redrawing. F₂ Lo (M Fx M
The example device shown is part of the seatback release mechanism. The part is subjected to a N-4 force exerted at A and a recovery moment of 300 - N • mm exerted by a hidden torsional spring. Determine y - the intersection of the line of action of the only equivalent force.
In the given figure below was supported at A and E by with a ball and socket and a wire at D connected to F. Determine the following given that force is equal to 687.4N: Determine the X-component of Vector DF Determine the Y-component of vector Df Determine the z- component of Vector Df Determine the moment experienced by the system assuming that there is no wire support. determine the x-component of the moment experienced by the system assuming there is no wire support Determine the y component of the moment experienced by the system assuming that there is no wire support Determine the z component of the moment experienced by the system assuming that there is no wire support determine the tension experienced by wire Df Determine the x component of the tension experienced by wire DF determine the y component of the tension experienced by wire DF Determine the z component of the tension experienced by wire DF Xb: 171. 995 xC : 477.445 Ya:200.266 ZE : 150.166 Zf : 492.252
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 16i - 13j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. Determine the magnitude of the moment of P about the y-axis in Nm. Determine the magnitude of the moment of P about the z-axis in Nm. Determine the magnitude of the moment of P about the origin (point O) in Nm.
A 4807 lb forklift used by Multi-National United is holding a 213 lb wooden block. Let z = 12in, y = 35in and z = 49in. 213 lbs 4807 bs A 12 in 35 in 49 in +x+y Determine the reaction at the front and rear wheels. To find the reaction at the front wheel, we'll use the moment on the (front/rear) wheel. The reaction on the front wheel is Ibs. To find the reaction at the rear wheel, we'll use the moment on the (front/rear) wheel. The reaction on the rear wheel is Ibs.
Find the moment about C & D, where AB = AD = 16 m, F,= 3 N, F2 = 6 N, F3 = 12 N & F4 = 16 N. Each force is acting at the mid-point of each side. F1 F2 F4 Fs (NOTE: ENTER ONLY THE VALUES BY REFERRING TO THE UNITS GIVEN IN THE BRACKET. ALSO, SUBMIT THE HANDWRITTEN ANSWER SHEET IN THE LINK PROVIDED) The moment of force about "C" (in Nm) = The moment of force about "D" (in Nm)
about the point (0). moments of these forces АВСD as 6N 3m 5m B 250 N 15% 1- Calculate the moment of the (300 N ) force on the handle of the monkey wrench about 200 mm 30 mm the center of the bolt . T00 mm hout point O.
Homework-3- 1. Calculate the moment at point (A) of the forces shown in figure. T;=10 2.5 m_-4 2.5 m - "-I T=3N т T3=6 N M=5 N.m T-4 N T3=2 N 0-45° 3 m 5 m 2. Determine the moment of a 90 N force about point C for the condition 0 = 15°. 600mm 9ÓN 3. Find the forces in member AB and BC by component method. C Tc 45 30 45° 30 Ring Pulley 60YB 200 N Pulley 200 N 200 N 200 N 4. Choose any question from (Ɛ ) and solve it as homework. 800mm
A member is loaded with the given system of forces Find the moment about C & D. Where AB = AD = 70 m, F1=35 N F2=50N, F3=63N, F4=48N, e1=35°, e2= 50°, 03=25° & 604=60°. (Enter only the values in the boxes by referring the unit given in brackets. Also upload your hand written answers in the link provided) shown in figure. F2 A D Өз F4 The Moment about "C" (in Nm) = The Moment about "D" (in Nm) =
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 19i - 10j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Magnitude of the reaction force at A in kN = 34.8 Determine the magnitude of the moment of P about the x-axis in Nm