Problem 3: A helical compression spring, manufactured using a music wire with a 45% of clastic limit. The spring has squared ends, 2 mm wire diameter, 10 active coils and 2.025 N/mm coil stiffness. Determine, a) The mean coil diameter. (Hint: Mean coil diameter is related to stiffness!). b) The force required to compress to solid-state without yield. =) The total length of the spring. I Whether the spring will buckle.

Problem 3: A helical compression spring, manufactured using a music wire with a 45% of clastic limit. The spring has squared ends, 2 mm wire diameter, 10 active coils and 2.025 N/mm coil stiffness. Determine, a) The mean coil diameter. (Hint: Mean coil diameter is related to stiffness!). b) The force required to compress to solid-state without yield. =) The total length of the spring. I Whether the spring will buckle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Design a helical spring for a spring loaded safety valve for the following conditions : Operating pressure Maximum pressure when thc valve blows off freely = 1 N/mm? = 1,075 N/mm? Maximum lift of the valve wvhen the pressure is 1.075 N/mm2 6 mm %3D Diameter of valve seat = 100 mm Maximum shear stress 400 MPa Modulus of rigidity = 86 kN/mm² Spring index [Ans. d= 17.2 mm; D=94.6 mm ; n = 12] 5.5 %3D
Parts A-C ( concern a helical compression spring with the following parameters. )circle final answer for each part PART A - What is the spring constant? Give your answer in units of N/mm. Part B - what is the stress at solidity? Give your answer in units of MPa Part C - what is the safety factor at solidity?
Stiffness of a helical spring decreases with increase in deflection Select one: O True O False
The spring constant of a helical compression spring DOES NOT depend on (A) coil diameter (B) material strength (C) number of active turns (D) wire diameter
Design a helical spring to be used in spring balance with a wire diameter of 6mm and the outside diameter should be limited to 66mm. if the permissible shear stress of the spring material is 325 N/mm? and the Modulus of rigidity is 85kN/mm?. a) Compute the deflection of spring per active turn and the axial load on the spring considering the effect of curvature, take Wahl's factor as Kw= 1.1 b) Calculate the value of axial load neglecting the effect of stress factor. **Note: Please upload your handwritten working/solution to the link provided. The value of Mean diameter of the spring in mm . The Spring Index is. Shear stress factor, neglecting curvature effect . Deflection per active turn in mm Axial Load W in N .. Axial Load W in N. considering effect of curvature .
What is Sines failure criterion in the design of helical compression springs ?
1. Design a compression helical spring to cary a load of 500 N with a deflection of 25 mm. The spring index may be taken as 8. Assume the following values for the spring material: Permissible shear stress 350 MPa Modulus of rigidity = 84 kN/mm2 4C – 1 + 4C – 4 0.615 Wahl's factor -, where C= spring index. [Ans. d= 5.893 mm; D=47.144 mm; n 6]
A helical compression spring is made with oil-tempered wire of diameter 0.2", mean coil diameter of 2", 12 total coils, 5" free length, and squared ends. (a) Find the solid length. (b) Find the force required to compress the spring to closure? (c) Find the factor of safety against yield when compressed to the solid length. (Hint: Uses Say= 0.5 Sut for shear strength.)
FOR HIBISCUS AND ROSE GROUPS A helical spring is made of No. 10 steel wire and has 20 active coils. The spring index is equal to 4.67. Loading is static. Use SI units and find the stress when the deflection is equal to 25 mm. (Ans. 1 = 477 MPa) %3D
Required information A helical compression spring is wound using music wire of diameter, d, 2.16 mm. The spring has an outside diameter, OD, of 27 mm with plain ground ends and 14 coils. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What should be the free length to ensure that the torsional stress does not exceed the yield strength when the spring is compressed solid? What is the critical free length? Is there a possibility that the spring might buckle in service? The free length should be |mm. The critical free length should be Buckling is likely Eto occur. mm.
Compression springs are the most common spring configuration that product manufacturer's turn to when enhanced product functionality is required. You are required to design a compression spring that is made of oil-tempered wire of 4-mm diameter with a spring index of C=10. The spring will operate inside a pipe, so buckling is not a problem and select the ends to be plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. a) Calculate the spring rate and the solid length. b) Calculate the total number of coils needed. c) Calculate the minimum pipe diameter for the spring to operate in. d) Calculate a static factor of safety based on the yielding of the spring if it is compressed to its solid length.
A helical compression spring is used to absorb heavy vibrations. Apply mechanical engineering design theory and by using the values given in the table below, (i) Calculate the force applied on the spring. (ii) Determine the number of turns. (iii) Determine the spring stiffness. (iv) Calculate the free length. 5 maiks (v) Would you recommend to increase the number of turns and free length of the spring for this application ? Why? (answer in one/two sentences only). Spring data Туре Helical squared and ground ends Initial Compression of spring 30 mm 80 mm Further Compression of spring after applying heavy load Shear Stress Modulus of rigidity 750 N/mm2 82000 MPa Wire diameter 8 mm Spring Index