Problem # 2: Determine the internal axial force in each member of the truss using the force method. Clearly indicate whether the member is in tension or compression. Assume AE is constant. Hint: When cutting extra member(s), recall that the "cut primary" truss still must transmit the load to the supports and must be stable! Thus, selecting which members to cut should be trivial here! 3 m 4 m- F B -4 m- C E 8 KN -4 m- D

Problem # 2: Determine the internal axial force in each member of the truss using the force method. Clearly indicate whether the member is in tension or compression. Assume AE is constant. Hint: When cutting extra member(s), recall that the "cut primary" truss still must transmit the load to the supports and must be stable! Thus, selecting which members to cut should be trivial here! 3 m 4 m- F B -4 m- C E 8 KN -4 m- D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2: For the below trusses. list the members that has NO axial force (Zero force members) under the load given. Each wrong answer cancels a right answer. FO co G H Truss DES Tuss-T3- H Truss-T2- B 20 KN Truss-T4- ↓ D D WW с B 50 KN E
Check the stability of truss.. Give me right solution with clear calculations.
1. Is this truss (simple, compound or complex )truss? 2. Determine the bar force in member AF of the truss shown in the figure below: * 20kN E D 2m A B 2m 2m G, 2m 2m 1 Add File
This truss contains diagonals that are not slender. F E D 3m 4 m- 4 m 10 kN 20 kN 10 kN Determine the forces in members AE, BE, FB in kN. (don't forget that compression is negative, "-") And what is the equation used to calculate truss degree of indeterminacy? j-r 3r - b (ktt) - 2j (bti) - 2r
4 kN 4 kN 3 kN 2 kN B C D 3 m H 2'm - 5 m- -5 m- -5 m- - 5 m- Q4- The figure shows a truss that is supported at A by a pin and a roller at E. The truss is subjected to vertical forces. Determine the following: (a) check for zero-force members and identify such members (b) The Force Reactions at the supports are: Ax kN Ay kN Ey k N (c) The internal Force in member CD, FcD i . kN, specify (T) or (C) (d) The internal Force in member CF, FCF İS. . kN, specify (T) or (C) (e) The internal Force in member CD, FcG is . kN, specify (T) or (C)
a. Draw FBD, and all necessary sketches. b. Find the reactions and the stresses in all the members of the truss as shown in the figure
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
Prob. 3 Is the truss statically determinate? Show your solution A F E B C
2. Determine all the internal members of the truss shown. Indicate if its compress tension. L BIOTO 3 m 3 m D 60 kN B 10 kN 6 m AC
1. Zero Force Members B T АЯ Identify the Zero Force Members in the Truss Structure below. C D E F G P INA MA O M L H 500lbf Q K
Determine the force in members EF, EP, and LK of the Baltimore bridge truss and state if the members are in tension or compression. Also, indicate all zero-force members. M L. K 2,m N P 2 m A B C DE F G H 2 kN 2 kN 5 kN 3 kN 8 @ 2 m = 16 m %3D
From the given trusses below, determine the force in the member EO. (kN) Hint: V =-20.9 kN Note: Use two (2) decimal places in the final answer. %3D M 15m L 75KN 75KN 9 oqual bays at 3.0 m cach