A beam having a tee-shaped cross section is subjected to equal (12 kN.m) bending moments, as shown in Figure. The centroid location (y-) is (110 mm) measured upward from bottom edge of stem, the moment of inertia about the z axis, is (Iz 18646000 mm4).Determine the maximum bending stress produced in the cross section. State whether the normal stress is tension (T) or compression *.(C) 100 mm 25 mm 12 kN-m 175 mm 150 mm 12 kN-m 25 mm 70.8 MPa (T) O 75.8 MPа (С С 45.0 MPa (T) O 30.8 MPa (C) O

A beam having a tee-shaped cross section is subjected to equal (12 kN.m) bending moments, as shown in Figure. The centroid location (y-) is (110 mm) measured upward from bottom edge of stem, the moment of inertia about the z axis, is (Iz 18646000 mm4).Determine the maximum bending stress produced in the cross section. State whether the normal stress is tension (T) or compression *.(C) 100 mm 25 mm 12 kN-m 175 mm 150 mm 12 kN-m 25 mm 70.8 MPa (T) O 75.8 MPа (С С 45.0 MPa (T) O 30.8 MPa (C) O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part 2,3,4
Prob 5. Calculate the maximum deflection dmax and the angle of deflection on the supports of a uniformly loaded simple beam loaded as shown. The maximum bending stress is o=60 MPa. The cross section of the beam is square with a length of 8 cm on each side. The beam is made of aluminum having modulus of elasticity E = 70 GPa. q = 2.0 kN/m L= 2.0 m
200mm Strain gauge F mun +100m 200mm- 4mm Strain gauge 4mm 12mm 12mm 4mm A small T-section is used in inverted positions as a beam and is shown in figure over a span of 400 mm. If due to the application of forces shown, the longitudinal strain gauge at F registers a compressive strain of 1500 microstraints, determine the magnitude of P. Take E = 200 GPa.
A beam carries concentrated loads at each ends, and a triangular load shown in figure. The beam is a built up shown below. Determine the maximum value of P if the allowable bending stress is1200 psi and the allowable shear stress 200 psi. W=3P P n 4 FT R1 12 FT R2 4 FT
W A L Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 b Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm B = 41 mm t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
The couple M=1.1 kN-m acts in a vertical plane and is applied to a beam oriented as shown. Determine the stress at point A 10 mm 40 mm The stress at point A is ( 10 mm 40 mm -10 mm 1,-1.894 x 10 mm 1,-0.614 x 10 mm +0.800 x 10 mm MPa.
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 2.6 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at C. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1m
The beam is subjected to a bending moment of M = 17 kN. m. σA = B 200 mm OB = 30 mm 30 mm M 30 mm 30 mm 50 mm 150 mm 150 mm 50 mm Part A Determine the bending stress in the beam at point A. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER: Q Tap image to zoom Part B Determine the bending stress in the beam at point B. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. ANSWER: