Problem 1 An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A, as shown in figure. The strength properties of the wire and the shear pin at B are ou = 350 MPa (wire), and t=300 MPa (pin at B). If the wire and pin are to be sized to provide a factor of safety of the wire F.S = 3.3 and a factor of safety of the pin F.S = 3.5. What are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)?

Problem 1 An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A, as shown in figure. The strength properties of the wire and the shear pin at B are ou = 350 MPa (wire), and t=300 MPa (pin at B). If the wire and pin are to be sized to provide a factor of safety of the wire F.S = 3.3 and a factor of safety of the pin F.S = 3.5. What are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An assembly of bars are designed in Figure 1. The assembly is made of structural A-36 steel where bar AB and BC has a drameter of 50 mm. ASTM and 25 mm The respectively. determine дар between C and the rigid wall at D is initially 0-15 mm, the support reaction at A and D when the force P= 292 kN is applied at B 600mm 450mm 292- A B D
T- B The overhang beam shown is supported by a pin at point A and roller at point 8. The beam is subjected to a uniformly-distributed load w, as shown. Which of the following best describes the shape of the internal shear (M) diagram between points B and C? O a) Cubic O b) Parabolic OC) Linear Od) Constant (non-zero) ) Zero
Problem 1 An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A, as shown in figure. The strength properties of the wire and the shear pin at B are , = 350 MPa (wire), and t-300 MPa (pin at B). If the wire and pin are to be sized to provide a factor of safety of the wire F.S = 3.3 and a factor of safety of the pin F.S = 3.5. What are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)? D 90 mm 20° 100 mm View a-a of B P = 2 kN
Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P at A. Diameter of wire CD is 1/8 of an inch and the diameter of the pin at B is 1/8 of an inch. Determine the tensile stress in wire CD and the direct shear stress in the pin at B. 150 P=300lb. -5 in- dw ↓ 1 4 in. D View a-a of B
The rigid bar AD (figure STR-4) is supported by two steel wires of 1.5mm diameter (E = 200 GPa) and a pin and bracket at D. Knowing that the wires were initially taut. Determine the following: a. The additional tension in wire BE when a load P=900 N is applied at D. b. The additional stress in wire FC when a load P = 900 N is applied at D c. The corresponding deflection at point D.
Solve for Ay and By with FBD. (Please mention no.of reaction forces in supports for better understanding)
G5 // The bar AB is considered to be absolutely rigid and is horizontal before the load of 10000N is applied. The connection at C is a pin, and AB is supported by the bronze rod EA and the steel rod FB. The length of EA is 1.5m and FB is 2.5m. Neglect any possibility of lateral buckling and the weights of all bars „Calculate the stresses in each rod. For bronze E=100 GPa, A=60 mm? for steel E=200 GPa, A= 25 mm? F Steel L=2.5m B. 3m 2m- Bronze L=1.5m 10000N
Please help with this practice question. Thanks Question 1 ) Determine the y-component of force at pin D.(The units should be in N)
See the diagram. Point A is a fixed connection. a) determine the normal force the pin at C exerts on the smooth slot. b) determine the components of the force at pin B. c) determine the components of the force at A. d) determine the external moment at A. Match the answer. 4 ft 50 I6 34 12 1 hormal force N = 296 62 68 328 S extermalUDment MAH 336 6. Notan answer 38 20
2) 60 mm The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm. T = 1600 N - m 36 mm determine the angle of twist at A. T = S00 N- m 250 mm 375 mm A 400 mm
Two reds vertically connect beam figure. Pcint A is fxed s shinged connected If the rod on the right is heated by 18 degree Celsius 2 m - 2 m 2 m Use E-200 GPa, linear of coeff cient expansion = 11.7x1o per degree celsius and A4509 mm Compute for the deformation of the right rodin mm Select the correct response 0.0234 mm 0.0842 mm 00468 mm 0.117 mm
The wooden strut is subjected to the loading shown. Draw the state of stress at point C on an infinite small element. The strut is supported by a bolt (pin) at point B and a roller support at point A. 50N S0N 40N 40 N -60 100 mm 50 mm 25 mm 200 mm 200 mm'200 mm'200 mm 100 mm 100 mm