Prob. 1.9, determine (a) the average shearing stress in the pin at A, and (b) the average bearing stress at A in member АВ. 45 mm 22 kN [Ans. (a) 51.2 MPa (b) -134.2 MPa] 22 kN 12 mm 60 PROBLEM 1.26 45 mm 45° For the assembly and loading of Prob. 1.9, determine (a) the average shearing stress in the pin at C, (b) the average bearing stress at C in member BC, and (c) the average bearing stress at B in member BC. [Ans. (a) 62.8 MPa (b) -164.4 MPa (c) -82.2 MPa] Fig. P1.9

Prob. 1.9, determine (a) the average shearing stress in the pin at A, and (b) the average bearing stress at A in member АВ. 45 mm 22 kN [Ans. (a) 51.2 MPa (b) -134.2 MPa] 22 kN 12 mm 60 PROBLEM 1.26 45 mm 45° For the assembly and loading of Prob. 1.9, determine (a) the average shearing stress in the pin at C, (b) the average bearing stress at C in member BC, and (c) the average bearing stress at B in member BC. [Ans. (a) 62.8 MPa (b) -164.4 MPa (c) -82.2 MPa] Fig. P1.9

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You plan to buy a $137,427 house. You have $32,117 to use as the down payment. The bank offers to loan you the remainder at 18% nominal interest compounded monthly. The term of the loan is 20 years. What is your equal monthly loan payment? Enter your answer as follow: 1234.56
1.1 A company compares two temperature instruments daily: one coupled to a processor computer and the other used for visual control. Day-to-day variation is expected. On each of three days, the two instruments are used to measure the temperature. Ideally, these two instruments should agree. How many factors are there in this experiment? What are they? List the levels for each factor.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
5 MPa 8 MPa 3 kPa Figure 2: The state of plane stresses. The state of plane stresses is as shown in Figure 2. a) Determine the state of plane stresses, if the plane in Figure 2 is rotated 40° counter clockwise. b) Determine the principal stresses, principal plane and maximum shearing stress.
QUESTION 5 Force A = 10N to the south and Force B 15 N to the east direction. Force C = Force A- Force B Angle of force C respective to East direction is... in degree angle. %3D QUESTION 6
1. Consider the temperature in a composite wall consisting of materials A,B,C which is shown below. Three materials' sizes are exactly equal. Top and bottom side of the wall is well insulated. We assume that thermophysical properties are all constant. Which two of the following are true A) Thermal resistance is largest in material A B) Theral resistance is largest in material B C) Heat is being generated within the wall D) Sign of heat rate is positive E) sign of heat rate is negative 2. Which two of the following are best correct statements for the wall with the temperature distribution shown below: A) The heat flux would be constant at any location in the wall B) It is unclear if heat is being generated within the wall C) Heat does not flow across the centerline D) Everywhere inside the wall, heat flows only to the right( same direction as the x-direction E) If the convection outside the wall is occuring with a normal magnitude of h, then it can be expected that Ts >>…
3- A loaded structure with a two-dimensional stress state has the stress in the x-axis is 13.5 Mpa, in the y-axis is - 3.2 Mpa, and the shear stress in the x-y is - 4.4 Mpa. a) Write the stress transformation equations b) Calculate o and t for the inclination angle 0 between the n values 0 to 180°, in 15° increments. c) Draw the profile graph of normal stress and shear stress with e in the x-axis d) Obtain from the graph, the principal stresses o,, o,, and 2' maximum and minimum shear stresses Tmax and tmin e) Obtain from the graph the corresponding inclination angle Op1, Op2, Os1, and es2 for each of principal stresses and shear stresses, respectively
5.22 What is the thermal resistance of 12.1 cm (4 3/4 in.) thick precast concrete (stone aggregate, oven dried)?
1-heat is defined as the average kinetic energy of the atoms and molecules that make up a substance and temperature is the amount of thermal energy transported2- heat is defined as the total kinetic energy of the atoms and molecules that make up a substance and temperature is the transport of pressure energy due to the temperature gradient3- Heat is defined as the average kinetic energy of the atoms and molecules that make up a substance and temperature is a measure of the equivalent kinetic energy of the individual molecules or atoms4- Heat is defined as the total kinetic energy of the atoms and molecules that make up a substance and temperature is a measure of the total kinetic energy of the individual molecules or atoms5- Heat is defined as the total kinetic energy of the atoms and molecules that make up a substance and temperature is a measure of the average kinetic energy of the individual molecules or atoms choose only one of the above alternatives as correct
QI) A) Determine the resultant force and its distance from the point A for the four forces shown in figure below when a=30. B) The value of a if the resultant force is applied at point B. 160 lb 100 lb 40ft 25 400 lb 30 ft (90 lb 600 D 10 t C 60 ft
Give information about tempering heat treatment temperature stages, microstructures formed and effects on mechanical properties.