Prob 2. (15pts) A line was found to be (2865.35+y)m long when measured with a 30-m tape under a steady pull of (6.5+y) kg at a mean temperature of 300c. Determine the correct length of the line if the tape used is of standard length at 200c under a pull of 5.5kg. Assume the cross-sectional area of tape to be 0.025cm2, elastic modulus as 2.10 x 106 kg/cm2, and coefficient of thermal expansion to be 0.0000116/@c.

Prob 2. (15pts) A line was found to be (2865.35+y)m long when measured with a 30-m tape under a steady pull of (6.5+y) kg at a mean temperature of 300c. Determine the correct length of the line if the tape used is of standard length at 200c under a pull of 5.5kg. Assume the cross-sectional area of tape to be 0.025cm2, elastic modulus as 2.10 x 106 kg/cm2, and coefficient of thermal expansion to be 0.0000116/@c.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 50-m steel has an error of 0.04 m at 20°C with a pull of 50 N. A rectangular lot is measured using this tape. The sides are recorded as 19.84 m and 10.21 m. The average temperature of the tape during measurement is 20°C with a pull of 50 N. The correct area of the lot in square meters is:
A steel tape is 100 m long at a temperature of 20°C and a pull of 10 kg. It was used to measure a distance of 624.95 m at a temperature of 32°C with an applied pull of 15 kg during measurement with the tape supported at both ends. Coefficient of thermal expansion is 0.0000116/°C and a modulus of elasticity of 2x106kg/cm2. Weight of tape is 0.04 kg/m and a cross sectional area of 0.06 cm2. a) Compute the sag correction. b) Compute the total correction for tension, sag and temperature.c) Compute the corrected length of the line by applying the combined corrections for tension, sag and temperature
A rectangular nylon [E =8 GPa; v=0.35; a= 23×106/°C] plate has a circular hole in its center. At an initial temperature of T₁ = 22°C, the plate widthis b=310 mm, the plate height is h = 220 mm, the diameter of the central holeis d = 60 mm, and the thickness of the plateist= 18 mm. At a final temperature of T= 59°C, determine (a) the diameter d of the central hole. (b) the thickness t of the plate. Answers: (a) d = i (b) t= i b d mm mm
Sample Problem 8.3 Solid shaft AB rotates at 480 rpm and transmits 30 kW from the motor to gears G and H; 20 kW is taken off at gear G and 10 kW at gear H. Knowing that tall = 50 MPa, determine the smallest permissible diameter for the shaft. 10- -200 →-200 200 → 200- H 160 GG E C D B A rc = 60 |M "D = 80 Dimensions in mm
I need the answer quickly
uidelines on formats and how to submit your solution. 1. Blocks B has a mass of 20 kg and block C has a mass of 15 kg. The coefficient of static friction at the contacting surfaces is 0.2. Block A is suspended by a rope that passes over a fixed cylinder and is attached to block B. The coefficient of static friction between the rope and the cylinder is 0.25. What is the largest mass block A can have without causing block B to slip the left?
Find the correction due to sag
Q-4,
MENG222 Strength of material please I have report lab ((Deflection Measurement for Simply Supported Beam)) please helpe me for that I need graph for this table thank you
Refer to the photo provided. Please make sure your handwriting is readable. Internal pressure and axial tensile force are applied to an open cylindrical tank 605 mm in diameter and 3.02 mm thick, resulting in the final stresses illustrated in the Mohr's circle. If a = 40.10 MPa, b = 100.06 MPa, and c = 45.05 MPa. 1. Determine the kPa value of the internal pressure. 2. What is the axial force's magnitude in kN?
3. Consider the following scenario: A civil engineering stadent measures the resistivity of a particular cytindrical wire for different lengths L by tapping at points the wire from 0.l m to 1 m in steps of 0.1 m The radms of the wire is 0.02 mm. The experiment is carried out under following circumstances: a) The best line has been drawn through the points given below and determine the resistivity of the wire from the slope of the plot between blue marked points. b) Based on the vahue of resistivity you calculated, what is the material wire resistor made of? Make sure everything is in ohms and meters, otherwise your units will not work out correctly in the end! Table 1. Resistivity of Some Common Materials. Material Silver Соррer Gold Aluminum Steel Lead Manganin (Cu. Mn. Ni alloy) Constantan (Cu, Ni alloy) Mercury Nichrome (N. Fe. Cr alloy) Resistivity p ( N-m) 1.59x 10 1.72x10 2.44 10 2.65x10 2x10 22x10 4.4x10 4.9x107 9.6x10 1-10 9. 8 7- 6- 5. 3. 2. 00 0.2 0.4 06 08 Lim)
Example 1.2 (a) A 25 mm diameter bar is subjected to an axial tensile load of 100 kN. Under the action of this load a 200 mm gauge length is found to extend 0.19 x 10-3 mm. Determine the modulus of elasticity for the bar material. (b) If, in order to reduce weight whilst keeping the external diameter constant, the bar is bored axially to produce a cylinder of uniform thickness, what is the maximum diameter of bore possible given that the maximum allowable stress is 240 MN/m2? The load can be assumed to remain constant at 100 kN. (c) What will be the change in the outside diameter of the bar under the limiting stress quoted in (b)? (E = 210 GN/m² and v = 0.3).