Please help me with this fluid mechanics question! Thank you!! :) A 1967 Harley-Davidson Shovelhead motorcycle uses a ventruri-carburetor to mix air and fuel for combustion. The venturi reduces the pressure to draw fuel from a reservoir chamber and to mix with the airstream as shown in the figure. The energy loss of the metering line is given by hL= (K*V^2)/2 where K = 6.0 and V is the fuel velocity in the metering line. Assume that the air is an ideal fluid (68°F). Calculate the mass flux of air and the mass flux of fuel. Hint: Assume the air intake velocity is negligible.

Please help me with this fluid mechanics question! Thank you!! :) A 1967 Harley-Davidson Shovelhead motorcycle uses a ventruri-carburetor to mix air and fuel for combustion. The venturi reduces the pressure to draw fuel from a reservoir chamber and to mix with the airstream as shown in the figure. The energy loss of the metering line is given by hL= (K*V^2)/2 where K = 6.0 and V is the fuel velocity in the metering line. Assume that the air is an ideal fluid (68°F). Calculate the mass flux of air and the mass flux of fuel. Hint: Assume the air intake velocity is negligible.

Name: Please help me with this fluid mechanics question! Thank you!! :)A 196
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Please help me with this fluid mechanics question! Thank you!! :)A 1967 Harley-Davidson Shovelhead motorcycle uses a ventruri-carburetor to mix air and fuel for combustion. The venturi reduces the pressure to draw fuel from a reservoir chamber and to

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter28: Gasoline, Diesel, And Other Fuels

Section: Chapter Questions

Problem 6RQ: List three alternative fuels for an internal combustion engine and briefly explain where they come...

See similar textbooks

Similar questions

Explain why a small PCV valve opening is adequate at idle speed.
bore and stroke of the fuel pump. 2. A 4-cylinder, 4-stroke, diesel engine, has the following parameters: brake power 100 hp, engine speed = 25 r.p.s, b.s.f.c. = 213 g/kW.hr, fuel density = 0.85 g/cm³, a = 1.2, and z = 1.25. Calculate: (i) Volume of fuel injected for one cylinder. (ii) Bore and stroke of the fuel pump. 3. A 4-stroko
C- Fill the blank 1- Internal combustion engines classified according to air intake into the cylinder to and-- 2- Typical compression ratio for modern gasoline engine lie between 3- There are a number of gasoline additives that are used to raise the octane number such as 4- Higher compression ratio in SI engine lead to 5- The thermal efficiency of CI engine is than of SI engine. 6- Fuel with octane number of 78 indicate 78%- -and 22%- 7- Anti-Knock quality improves with - no. of carbon atoms. 8- Higher compression ratio in SI engine lead to 9- Maximum power overtaking a vehicle or climbing up a hill (extra load) this requires a mixture.
Question 3 A four-cylinder of 1.6 liters S.I engine (S4PH with BSFC = 0.5 lb/HP- hour) has the specification as follows: ü Injector size = 240 c.c/min with the fuel pressure set at 43.5 p.s.i ü I.D.C = 80% at W.O.T Calculate: i. Current S4PH engine horse power ii. The new injector flow rate, if we raise the fuel pressure at 50 p.s.i [lb/hour] iii. The new fuel system's horse power capacity iv. The % HP enhancement
List out the design requirements of diesel engine combustion chamber
Asap
In a negative backpressure EGR valve, if the exhaust pressure passage in the stem is plugged, the bleed valve remains.
10 m3/min of free air is to be compressed to 8 bar gauge in two stages. Assuming an intercooler pressure of 2 bar gauge and polytropic index of 1.3, what will be the flowrate at the exit of the intercooler ?Please choose correct option.a.4.295 m3/minb.312 litre/sec.c.3333 litre/mind.1172 litre/min.e.981 m3/min
Engine Type: Single cylinder Four stroke Diesel engine, Bore: 0.0875m, Stroke: 0.11m Capacity: 661.5 cc, Power: 6 H.P. at 1500 rpm, Torque: 2.96 kg.m at 1500 rpm and Compression Ratio :17.5:1 Explain how to measure the :- Fuel consumption. Inclined manometer readings for air flow. RPM, power output etc. (iv) Study of various components of diesel engine. (ii)
Q1/ Compare between the following: 1- Swirl and crevice flow motions. 2- S.I and C.I fuel injectors. 3- Octane and cetane numbers. 4- Pressurized and splash methods
The most popular combustion chamber.7 which is equipped with four valves per :cylinder is Hemispherical Head O Wedge Chamber Pent-roof head .Bath-tube head „All of the above It is important to have sufficient turbulence.8 motion in order to Speed evaporation of the fuel „Enhance air-fuel mixing Increase combustion speed and efficiency Reduce the time for auto-ignition to .occur All of the above
INTRODUCTION ABOUT VALVE SYSTEM IN INTERNAL COMBUSTION ENGINE