Structural Analysis
6th Edition
ISBN: 9781337630931
Author: KASSIMALI, Aslam.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Question
Please annotate the attached image to highlight the different phases of a polymer stress/strain graph.
From the attached graph, calculate the following:
1-modulus of elasticity
2-tensile strength
3-the ductility in % of elongation
4- yield strength at a strain offset of 0.002
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by stepSolved in 6 steps with 7 images
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Briefly explain the (a) how and (b) why the size of elastic deformation changes as the thickness of the specimen increases when a rod-shaped specimen made of the same material is bent.arrow_forwardIf Poisson's ratio is 0.42, the Modulus of rigidity is 70.4225 GPa, and the bulk modulus is 416.66 GPa, then the elastic modulus of elasticity is (3 Points) 300 GPa 300 MPa 200 MPa None 200 GPaarrow_forward1. The tensile strength vs. temperature curves of aluminum are plotted below. Explain the meaning of these two curves. 400 Ultimate strength 300 Yield strength 200 100 -200 -150 -100 -50 50 100 150 200 250 Temperature, °C Strength, kPaarrow_forward
- For material, the modulus of rigidity is 100 GPa and the modulus of elasticity is 250 GPa. The value of the Poisson's ratio isarrow_forwardGiven your understanding of what initiates and controls failure in materials, which of the following will increase the failure strength or lifetime of a test piece or component and why? a. Decreasing the difference between the maximum and minimum stress values, as this effects the stress concentration factor b. Decreasing the temperature below the brittle-ductile transition temperature, to make it harder C. Polishing to reduce surface defects Od. Increasing its volume, to give a larger cross sectional area Oe. Increasing the grain size so there are less grain boundaries to initiate failurearrow_forwardUsing the Stress-Strain diagram for polymers below, identify the types of polymers depicted based on their Stress-Strain behavior/curve 60 A 50 40 30 В 20 C 10 1 2 4 5 6 7 8 Strain A. [ Choose ] B [ Choose ] [ Choose ] > 3. Stress (MPa)arrow_forward
- A steel bar has a length of 2.5 m and cross-section of 200-mm x 100-mm. The modulus of elasticity of this material is 210 GPa and Poison's Ratio is 0.3. The change in width after applying a tensile force of 150 kN is?arrow_forwardA round steel alloy bar with a diameter of 19mm and a gauge length of 76mm was subjected to tension, with the results shown in Table. Using a computer spreadsheet program, plot the stress–strain relationship. From the graph, determine the Young’s modulus of the steel alloy and the deformation corresponding to a 37kN load.arrow_forwardAn elastoplastic material with strain hardening has the stress–strain relationship shown in Figure 1.6(c). The modulus of elasticity is 175 GPa, yield strength is 480 MPa, and the slope of the strain-hardening portion of the stress–strain diagramis 20.7 GPa.a. Calculate the strain that corresponds to a stress of 550 MPa.b. If the 550-MPa stress is removed, calculate the permanent strain.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSONPrinciples of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
- Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill EducationTraffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning