Place the correct formula in theblank%To determine Generated Power Output ofWind turbineclcclear allI=42;v=17;ad=1.23;cp=0.6;ng=0.96;nb=0.73;pw=0.5*ad*area*v^3pt=pw*cpp=pt*ng*nbpmw=p/1000000area=pi*l^3 | area=pi*l^2 || area=pt*I^2area=p*l^2

Given:- Wind turbine:- To find- Power formula

Answered: Place the correct formula in the blank…

Engineering

Mechanical Engineering

Place the correct formula in the blank %To determine Generated Power Output of Wind turbine

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the figure shown below, what flow rate is required to produce 4,700 HP if the turbine is 72% efficient? D = 3 ft L 3,600 ft f=.026 11 MGD O 16 MGD 20 MGD O 25 MGD Az = 2,300 ft T Minor Loss Kent = 0.8 Kvalve = 5 Kelbow = 0.66 x 3 Kbend = 0.47 Kvalve = 2.2 Kexit = 1.0
5. Calculate the swept volume and mean effective pressure (MEP) of a 4-Cylinder, 2-stroke IC engine that has the following particulars: (Show the computation) Engine speed = 3000 rpm, bore = 120 mm, crank radius = 60 mm, Mechanical efficiency = 90% and the engine develops 75 bhp.
The array spacing is 5D by 10D, for 1 MW wind turbines, 60 mdiameter.a. How many turbines can be placed in a square kilometer?b. Assuming the average wind power potential is 500 W/m2 at 50 mheight and the capacity factor of 35%, estimate the annual energyproduction for each turbine and the designed wind farm.c. Calculate the cost of gearbox for each turbine if a medium speedgenerator is used. In what condition you can eliminate that cost?
Each project should be presented in written and oral forms. A written individual report should contain a summary, introduction, short literature review, objectives, methodology, results and discussion and conclusion. Project 1 A vortex tube is a mechanical-thermal device that separates a compressed flow of air (or any inert gas) into hot and cold streams and has no mechanical moving parts. Cold Air Compressed Air Supply Vortex Spin Chamber (2 cold outlet f = 0.25 P₁ = 100 kPa d. e. Develop the main equations f. Estimate the COP with and without the vortex tube. https://blog.exair.com/2018/10/31/the-theory-of-the-vortex-tube/ a. Start by solving using the simple problem (problem 1) described below. b. Derive the basic equations allowing its performance evaluation. c. Develop an EES model and conduct an analysis on the thermal performance of this device. Consider three working fluids. Consider the integration of the vortex tube with a refrigeration system. Control Valve Hot Air 6 Problem…
1. An axial flow water pump is based upon the free-vortex design. The mean diameter velocity diagram has an axial inlet with a flow coefficient of 0.3 and a work coefficient of 0.208. The tip diameter to mean diameter and the hub diameter to mean diameter ratios are 1.25 and 0.75 respectively. The blade velocity at the mean diameter is 60 m/s. Find and draw the velocity diagrams at the mean, hub and tip diameters. Show all velocities and angles on the velocity diagrams. {..
Subject: Combustion Engineering A rankine cycle has the specific conditions: Inlet of turbine: T= 368 degree celcius p= 11.17 mPa condenser pressure= 550 kpa specific volume= 1.0967×10^-3 m³/kg use g= 9.81 m/s² Consider water to be incompressible, do not neglect the pump work. Find the total dynamic head in mm if the mass flow rate is 120 kg/s.
What is the engine speed (in rpm) required for good volumetric efficiency for a square engine with one inlet and one exhaust valve, bore of 0.086 m, inlet air temperature of 327 K, exhaust temperature of 875 K and exhaust valve diameter 31.9 mm. Assume specific heat ratio =1.32, R = 287 J/kg.K, an average inlet flow coefficient 0.37 and an average exhaust flow coefficient 0.47. Select one: a. 7150 b. 7800 c. 5620 d. 8640 e. 9200
Siven Quation 2 According to figure 1, Given data as (COP)HP =3.5, QH= 90000 KJ/h (rate) and 1KW = KJ/S (rate) a) Calculate W net in KJ/h ? b) Calculate Wnet in kilo watt (Kw) %3D Quation 3 Given data as Wnet = 98000.0 KJ/h (rate) and QH= 75000.0KJ/h(rate) a) Calculate Q in KJ/h ? b) Calculate QL in Kilo watt(KW) Quation 4 Given data QL=400.0 KJ/min (rate) and Wnet =3KW(rate) Calculat (COP)R?
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW find the following: fuel consumption m'f = kg/ sec the air consumption engine capacity.: the flow rate of air intake to cylinder the Volumetric efficiency
b) A single stage, single acting reciprocating compressor has a bore of 250 mm and a stroke of 550 mm. It runs at a speed of 300 rev/min. The clearance is 4% of swept volume, and the polytropic index is 1.39 throughout. The intake pressure is 97 kPa at 25°C, and the final compression pressure is 600 kPa. If the free air conditions are 101 kPa and 20°C, determine the free air delivered in m/s.
Q2) Design a Francis turbine with the following specifications: Head available 68m Speed Power output Hydraulic efficiency Overall efficiency Flow ratio X 750 rpm 330kw 94% 85% 0. 15 0.1 Breadth to diameter ratio at inlet Outer to inner diameter ratio 1/2 Assume 6% of circumferential area of runner occupied by thickness of vanes and flow velocity remains constant and flow is radial at exit.
What is the engine speed (in rpm) required for good volumetric efficiency for an engine with two inlet and two exhaust valves, bore of 0.086 m, stroke of 90 mm, inlet air temperature of 330 K, exhaust temperature of 900 K and inlet valve diameter 30 mm (each). Assume specific heat ratio =1.37, R = 287 J/kg.K and an average inlet flow coefficient 0.4. Select one: a. 7013 O b. 6350 O c. 7847 O d. 4620 e. 9202