%VAI۲,۷K/s9:- Zain 4.5G+A step down de chopper is connected to an R-52 and L. 10 mH. The de supply voltage is100 V. The chopper is switching at a frequency of 1 kHz with a duty cycle of 50%. Determinethe load current, Jo and the peak to peak ripple current as an absolute value and as percentageof de value.☐ОΔ

Answered: Image /qna-images/answer/32a24ace-ee16-411b-97b6-7c0c63f8afc2.jpg

Answered: %VAI ۲,۷ K/s 9:- Zain 4.5G+ A step down…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What types of PWM is shown in the figure? * Modulating Waveform Carrier waveform A (b) 44444 F -V O Unipolar O Bipolar 000
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
Design of a DC-DC Converter. The Circuit Below shows a basic Buck-Boost Converter with a highly inductive Load. With a Deliberate mistake in the configuration of the Circuit Connection. The Value of L1 is 22mH, C1 is 10uF, R1 is 220 and L2 is 10mH. The circuit operates with a switching frequency of 20KHZ. The Duty cycle of the Clock signal V2 is given by the function below: ( 17 ) х0.2 Duty Cycle, k = 0. 55 + 100 Your Unique Duty Cycle = %3D Buck-Boost Converter Q1 IRG4BC10U D1 R1 222 1N4009 C1 LV1 12V L1 22mH 10µF L2 10mH a) Find the mistake in the configuration of the circuit and correct the connection error.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 RL out OV 10 kN IN4001 alll
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R 10 kn IN4001
An unipolar PWM full bridge circuit has a Vr.rms of 125V at a duty cycle D1 of 0.7. What is Vd? What is Vo.rms?
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 10.2-0-10.2 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D, SCT RL D. llle ண
What is the value of the average voltage at the output of the circuit in the figure, knowing that: Voltage at the transformer output is equal to 5 Vac and the four diodes are from the 1N4001 family.
A single phase full converter feeds power to RLE load with R=10 ohm, L=10 mH and E=50 V, the ac source voltage is 230 V, 50 Hz. For continuous conduction, what is the average value of load current for firing angle delay of 600 ?
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 R. V out OV 10 kN D2 IN4001 llle

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS