An LM317 is connected between two decoupling capacitors. There is a 220ohm resistor between the output pin and the adjust pin . Note the voltage drop between the output and adjust pins is 1.25V. Find the resistor needed between the Adjust pin and ground to ensure 5 V is dropped across the load. Enter your answer in ohms: _ohms

An LM317 is connected between two decoupling capacitors. There is a 220ohm resistor between the output pin and the adjust pin . Note the voltage drop between the output and adjust pins is 1.25V. Find the resistor needed between the Adjust pin and ground to ensure 5 V is dropped across the load. Enter your answer in ohms: _ohms

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4 Listed are some of the uses of capacitors except: A. couples AC B. bypassing a shunt load C. signal amplification D. filters pulsating DC
A charging circuit that will deliver constant DC current will be designed. The input of the circuit is 220V / 50Hz AC and its outputIt will be 5V / 2A DC.The circuit will consist of 3 parts:AC transformer will reduce the voltage on the inputii. AC rectifier circuit will convert low AC voltage to DCiii. Current source, this part will keep the current at the output constant.You determine the transformer drop rate in the first part. Its output is low voltage ACas the source and design the second and third parts accordingly.
Q5) The schematic circuit in PLECS for a single-phase rectifier is shown below, Q5) The schematic circuit in PLECS for a single-phase rectifier is shown below, Thyristor Crout Probe Pulse Generator VC, pulses Probe Scope Thy Orso v Joad O R: 1 The output voltage across R is depicted in 0.5 0.0- b) 0.2 0.0 d)
Moving to another question will save this response. Quèstion 3 In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases. True False Moving to another question will save this response. to search 近

a. What is the effect of applying reverse voltage on a pn junction? b. What is the critical electric field and when will it happen?
In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases. True or false
a. If you do not go completely around the loop when applying Kirchhoff’s voltage law, then the algebraic sum of the voltages cannot be determined the algebraic sum of the voltages will always be positive the algebraic sum of the voltages will always be negative the algebraic sum is the voltage between the start and finish points b. A p -type semiconductor is a semiconductor doped with impurity atoms whose electron valence is +4 pentavalent impurity atoms trivalent impurity atoms
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R 10 kn IN4001
An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) DI IN4001 R1 out OV 10 kN IN4001 elle lelll
A three phase full wave rectifier is shown below. The input phase voltage peak is Vm=311.128 V. The load is purely resistive of value 52. The DC and RMS output voltages are respectively equal to: Secondary 太D太D,太D, 太D。太De太D, b. Select one: O a. 180V, 240.2V O b. 514.6V, 515.04V O c. 180V, 197.2V O d. 220V, 249.2V
Determine 1) the maximum load current. 2) the mean load current .3)the rms alternating load current. 4) the DC power supplied to the load. 5) the input power to the anode circuit. 6) the rectification efficiency. 7) the percentage of regulation. 8) the ripple current. R=10°0 Vi R=10°n AC Figure (2-72) the circuit of problem (2-6). (2-7) A full-wave bridge rectifier with a 120 Vrms sinusoidal input has a load resistance of Ikn. Determine:- 1) The de voltage available at the load. 2) Find the maximum current through each diode during conduction. 3) What is the required power rating of each diode. (2-8) A zener diode has a de power dissipation of Iw and a zener voltage rating of 27v. What is the value of I, max for the device? (2-9) Calculate and draw the output voltage for the circuit shown in Figure (2-74). +100v Vo 2.2kd4 2.2kQ -100v Figure (2-74) the circuit of problem (2-10).