P/02 26 L P 75⁰ A 500mm diameter pipeline carries water at 20deg Celsius under a head of 25m with a velocity of 2.5m/s. This water main is fitted with a horizontal bend which turns the axis of the pipeline through 75 deg. Calculate the resultant force on the bend and its angle to the horizontal. *

P/02 26 L P 75⁰ A 500mm diameter pipeline carries water at 20deg Celsius under a head of 25m with a velocity of 2.5m/s. This water main is fitted with a horizontal bend which turns the axis of the pipeline through 75 deg. Calculate the resultant force on the bend and its angle to the horizontal. *

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please help me answer this problem ASAP badly needed. Thank you
fluid kimematics mechanical, A crude oil having kinematic viscosity of 0.4×10-4 m2 per second is flowing through a pipe having diameter 0.3 m at the rate of 300 litres per sec. calculate the head lost due to friction for a length of 50 m of the pipe?
Q.6 The velocity profile in fully developed laminar flow in a pipe of diameter Dis given by u=u (1-4r2/D²), whereris the radial distance from the center. If the viscosity of the fluid is u, the pressure drop across a length L of the pipe is %3D
What’s the answer for this please ?
(Q)A pump running at 1,440 rpm has to support a load of 10 kN. Journal diameter is 130 mm. Design a suitable Finite hydrodynamic journal bearing (L/D=1) with radial clearance of 0.065mm. The inlet oil film temperature is 450C. Calculate the bearing characteristics and the required heat dissipation. *
- Energy equation For steady incompressible flow for one Inlet and one outlet system Power form: W A In terms of Heads: P A P.X 2g sh mgh, POR.. Reynolds Number Re= Power = mass flux g hight: = mgh Wigh P Inertial forces V.,D Viscous forces P D. - Formula sheet 44, Cross sectional are P Print 2100 Res 4000 +α +²₂++h₂ VDpVD Flow in circular pipes Re 2300 laminar flow transitional flow Re 4000 turbulent flow 2x " +1+E₁ Determine: a. The length of segment B (La). b. The total pressure drop (pi-P2). Ch Welke PD Levve Aut L = 250 m O Correction Factor: o Laminar pipe flow : a = 2 o Turbulent flow in a pipe: a = 1 150 m с Beter Au Question 1 For the horizontal series-parallel system of the figure below, all pipes are 7 cm diameter asphalted cast iron (r= 0.12 mm) filled with water at 20°C (- 998 kg/m', -0.001 kg/m.s). The total flow rate is Q-0.0269 m/s, the lengths of segments A and Care LA-250 m and Le - 150 m, and velocity in segment A is l'A- 2.04 m/s. Neglect all minor losses. A (hem 2…
Q5. In a laminar pipe flow that is fully developed, the axial velocity profile is given as 1/2 as is illustrated in the figure below. What is the axial direction momentum flowrate calculated with the above velocity distribution?
a wind tunnel has the following flow properties at the inlet: P = 101,000 Pa; A = 1 sq.m; T = 288 K; V = 200m/s and in the test section, A = 0.25 sq.m and V = 900 m/s. What is the mass flow rate in the wind tunnel?
Air (diatomic, MW = 28.8664 g/mol) at 1.7 atm gage (where Pam = 1 atm) and 15°C enters a 70-m long horizontal 75-mm-ID steel pipe (€ = 4.6(10) m). The velocity at the entrance of the pipe is 60 m/s. Assuming isothermal flow, what is the absolute pressure (atm) at the discharge end of the line? Use Churchill equation for the friction factor.
A smooth square cylinder is put in 15 °C flowing water. The flow direction is perpendicular to the long axis of the cylinder (parallel to the square section). The edge length of the square is s=2.0m. The long axis length is L=5.0m. The flow velocity is v=0.046 m/s. The density of water is ρ=1000kg/m3. T he dynamic viscosity is η=1.15×10-3kg/m·s. (3) Calculate the drag force FD_________N (2 decimal places)
7. For the flow of a thin layer of liquid down an inclined plane shown: a. Using the cross-hatched element and through a force balance, show that the velocity distribution across the layer is: dx Y sin e (b2 – s2) 2 µ и 3 Free Surface an expression for the at the free b. Derive t dx liquid velocity surface. c. Derive an discharge per unit width. d. Derive Fixed y s dx expression for the Wall b an expression for the shear stress at the fixed wall.