P 8.5 A single circuit three phase 220kV line runs at no load. Voltage at the receiving end of the line is 210kV. Find the sending end voltage, if the line has resistance of 20.5 ohms, reactance of 81.3 ohms and the total susceptance as 5.45 x 10* mho. The transmission line is to be represented by R-model.

P 8.5 A single circuit three phase 220kV line runs at no load. Voltage at the receiving end of the line is 210kV. Find the sending end voltage, if the line has resistance of 20.5 ohms, reactance of 81.3 ohms and the total susceptance as 5.45 x 10* mho. The transmission line is to be represented by R-model.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
One circuit of a single-phase transmission line is composed of three solid 0.12" radius wires. The return circuit is composed of two 0.15" radius wires. Find the inductance of the complete line in mH/mi. The distance between wires are 40" horizontally and 25" vertically. A. 2.54 mH/mi B. 2.478 mH/mi C. 2.488 mH/mi D. 2.567 mH/mi Provide Clear Explaination
The impedance per phase of a 3-phase transmission line on a base of 100 MVA and 100 kV is 2 p.u. The value of this impedance on a base of 400 MVA and 400 kV would be?
Power in a three phase delta system with balanced load is equal to (Sqrt (3)) (VL) (IL) (p.f.) (Sqrt (3)) (Vph) (Iph) (p.f.) (Sqrt (3)) (VL) (Iph) (p.f.) O (Sqrt (3)) (Vph) (IL) (p.f.)
Select the base voltages for one section and calculate the base voltages for the rest of the sections. Remember that the voltages given are line-line. Calculate the current and impedance for all sections of the System. Assume a base complex power of 100 MVA.
If a 3-phase short circuit occurs in one of the two circuit of transmission line at point F, and the shunt impedance of the short circuit is j0.1 pu. Determine the maximum time when a short circuit can still be cleared. So=0.8+j0.3 Xd'= 0.2, XL1=XL2= 0.6, XT1=0.12, Xr2= 0.1, L1 V= 1.0 T1 L2 F T2 .XL= 0.1 Хс- 0.1. S1 S2 SL= 0.6+j0.3
A 3-phase, 132 kV, 50 Hz, and 200 km line has a resistance of 0.0765 ohm per km per phase, inductance of 0.605 mH per km per phase, and shunt admittance is 4.79 nF per km per phase. It delivers 40 MVA at 0.8 power factor lagging. Find the voltage regulation and transmission efficiency. Use nominal n circuit. --------
In the following network, the voltage magnitudes at all buses are equal to 1 p.u., the voltage phase angles are very small, and the line resistances are negligible. All the line reactances are equal to j1 p.u. (1) (2. P₂ = 0.1 p.u. P3 = 0.2 p.u. The voltage phase angle 83 in radian at bus 3 is (Assume one of the generator bus as slack bus and sin-¹ (0.1) = 0.1 rad) (a) -0.1 (b) -0.2 (c) 0.1 (d) 0
Which of the following combinations comprise the Transmission Line Impedance? O A. Conductance and Capacitive Reactance in Parallel O B. Conductance and Inductive Reactance in Parallel O C. Resistance and Inductive Reactance in Series O D. Resistance and Capacitive Reactance in Series
2. A three-phase transmission line has parameters Xc-6 k 2, R-3.25 2 and X₁-25 92, and delivers 300 MW to a load with both ends of the line at 230 kV. Draw a pi equivalent per-phase circuit of the line. On a per-phase basis, calculate the active power delivered to the load, the reactive power of the line and the active power delivered by the source. Based on these calculations can the equivalent circuit be simplified further?