In order to pull out the nail at B, the force F exerted on the handle of the hammer mustproduce a clockwise moment of 340 lb in about point A. (Figure 1)FigureA==18 in.30°5 in.1141 of 1Part ADetermine the required magnitude of force F.Express your answer with the appropriate units.μÅF =SubmitValueProvide FeedbackRequest AnswerUnits?

Answered: Image /qna-images/answer/c083160e-4fb4-4931-88cb-3d89f98dec0d.jpg

order to pull out the nail at B, the force F exerted on the handle of the hammer must oduce a clockwise moment of 340 lb in about point A. (Figure 1) ure 18 in. 30° 5 in. 1 of 1 Part A Determine the required magnitude of force F. Express your answer with the appropriate units. F= Submit O HÅ Value Provide Feedback Request Answer Units ?

order to pull out the nail at B, the force F exerted on the handle of the hammer must oduce a clockwise moment of 340 lb in about point A. (Figure 1) ure 18 in. 30° 5 in. 1 of 1 Part A Determine the required magnitude of force F. Express your answer with the appropriate units. F= Submit O HÅ Value Provide Feedback Request Answer Units ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3 Homework.pdf 1 من 1 EAAMPLE (1). A circular bar having 200 mm² area is subjected to axial loads as shown in Fig Find the value of ( P) and the total elongation . Take E=2*105N/mm2. A B 50kN 50kN -lokN 1M 1M 1M
A beam is shown with a distributed loading force 3 kN. Determine an equation for the shear force and bending moment as a function of the distance □ from its mounting point at B. Plot the functions from 0 < <3 and determine the magnitude of the maximum value in that interval. 3kN T A B [ V(x) L 3 KN. (Hand written and clean writing please )
Problem Set 5.pdf O File | C:/Users/naswe/Downloads/Problem%20Set%205.pdf OD ... (D Page view A Read aloud T Add text V Draw E Highlight Erase 2 of 2 5. Draw free body diagram without writing shear and moment equation of beam shown in Figure 2.19. Give numerical values at all change of loading positions and at all points of zero shear. Where P = 1kN P P P P P 1.0m 4.0m 1.0m Figure 2.19 1:05 pm 06/01/2022 ENG US
Figure STS 003 shows a pole acted upon by three forces. 4500.0 3842.2 4123.4 30" 3603.6 641 lb 30" 30" STC 003 Refer to figure STC 003. If the resultant is to be replaced by a couple-force system acting at base B, what will be the value of the couple in lb*in Select the correct response: B 300 lb 250 lb
QUESTION 4: LONG QUESTIONS Which of the following forces in the Figure below has the moment about point A equals 54 Nm, Anticlockwise ..? (NB. Each section represents 9 m"). NB. Elaborate on your answer in terms of calculations. 10N 8N 34 N15 12 26 N
Suppose that d = 0.14 m in (Figure 1). Part A Determine the angle at which the 500-N force must act at A so that the moment of this force about point B is equal to zero. Express your answer in degrees to three significant figures. 0= Submit VE ΑΣΦ | 41 Request Answer Figure vec 1 m B ISWE ? 2 m-
SITUATION. A three-legged stool is subjected to the load L as shown. Neglect weight of the stool. 100 325 120 120 120 Dimenaions in millimeters Q Zoom image Determine the vertical force reaction under leg A. O 0.667L O 0.233L 0.533L 0.166L
attempt- 138326&cmid-4951 GGoogle O UVLe: Log in to the.. table 4. Which of the following shows an appropriate diagram of the tension forces acting on the ring such that it is possible for the resultant to be a zero vector? Note that the value of G is not equal to H. Hint: The eraser does not slide if the resultant of the frictional force and normal force is vertical. 5. Which of the following best approximates the value of the angle h (in degrees) if G = 100 N and H = 75 N? acer E11 NumLk Verr. Num F9 F10 F7 F8 F4 F5 F6 E3 8. 9) & 7 24 9. 6. U 4 5 0 6 P R H. 1 K 2 L G. MO CO
ΕΧΑMPLΕ 1) A circular bar having 200 mm? area is subjected to axial loads as shown in Fig „Find the value of ( P) and the total elongation . Take E=2*10° N/mm?. A в C D 50kN 50kN -lo kN 1M 1M 1M
Asap
A rectangular plate is acted upon by the force and couple shown. This system is to be replaced with a single equivalent force. The force acting at point B is FB = 53 N. 240 mm D 15 N The value of a is[ 400 mm FB or B C Determine the value of a if the line of action of the equivalent force is to intersect line CD 300 mm to the right of D. 15 N I understand that the Magnitude of the Equivalent Force is 53N and the line of action F' intersects line AB at 0.130m to the left of B. However, I'm having a hard time determining the value of a if the line of action of the equivalent force is to intersect line CD 300mm to right of D. Please make sure your work is clear and legible. Thx!
SITUATION. A three-legged stool is subjected to the load L as shown. Neglect weight of the stool. 75 75 100 B. 325 120 120 120 Dimensions in millimeters Zoom image Determine the vertical force reaction under leg B 0.667L O 0.233L 0.166L 0.533L