For a second-order system that yields a 15% overshoot and a settling time of 0.7 seconds, determinethe following: Damping Ratio, Natural Frequency, Rise Time, Peak time and the General 2nd Order

Answered: Image /qna-images/answer/752afd35-80ce-46b9-b166-292e584a2b9d.jpg

Answered: or a second-order system that yields a…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The effect/effects of increasing the damping ratio 5 of a second-order system is/are O a. The maximum overshoot decreases and the damped frequency decreases O b. The settling time decreases and the peak time increases O c. The maximum overshoot increases and the damped frequency decreases O d. The settling time decreases and the peak time decreases
A series circuit consists of a resistor, a coil, and a capacitor connected across a 300 V, 60 Hz AC source. THe current drawn is 20A. The voltage across the resistor is 60 V, that across the coil is 260 V and that across the capacitor is 100V. The resultant voltage across the coil and the capacitor is 254.56 V. Determine (a) the resistance of the resistor, (b) the resistance and inductance of the coil, and (c) the resistance and capacitance of the capacitor.
TOPIC: STABILITY Subject to a step input, the voltage drop across the resistor took 696.3103us to reach 13% of its steady value from rest. Determine the time (ms) needed to reach 90% of its steady value from 10% Determine the time (ms) needed to reach 80% of its steady value from 20%
A sinusoidal voltage has a value of 100 volts at 2.5 milliseconds and takes 20 milliseconds to complete one cycle. Then find the maximum cost and the time to reach it for the first time.
A capacitor "C", an inductor "L" and a switch "S" are connected in series. When the switch is open, the plate to the left of the capacitor has charge "Qo". The switch is closed the load and current vary sinusoidally with time. Represent graphically the load "Qo" and the intensity of current "I" as a function of time "t", and explain why the current leads the load by a phase difference of 90°.
A sinusoidal voltage has a value of 100 volts at 2.5 milliseconds and completes one cycle.It takes 20 milliseconds. Then find the maximum cost and the time to reach it for the first time
A capacitor in series with a 200 ohms resistor draws a current of 0.3 ampere from 120 volts, 60 hz source. What is the value of the capacitor in microfarad? a. 8.7 b. 9.7 c. 6.7 d. 7.7
For the circuit below assuming an ideal switch, preform transient analysis to predict the voltage across resistor, R2 and plot the results. The inductor will have zero current as initial condition. L1 0.005 2 U1 100mH R1 1k V1 20Vdc R2 100
a.) determine the undamped natural frequency b.) determine the damping ratio c.) determine the type of system ( over damped, under damped, undamped, or critically damped )
The sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 50 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3.6 cm and the peak to peak height is 5.8 cm. Determine the following: The frequency is = The peak to peak voltage is = The amplitude is = The R.M.S voltage is =
For the network shown in figure (3), if the switch is closed for 2usec and then opened for Susec, find mathematical expressions for vi and in of both periods of time and then plot the waveforms of vL and i as a function of time.
A 1,000-W electric motor is connected to a sourceof 120 Vms, 60 Hz, and the result is a lagging pf of 0.8.To correct the pf to 0.95 lagging, a capacitor is placedin parallel with the motor. Calculate the current drawnfrom the source with and without the capacitorconnected. Determine the value of the capacitorrequired to make the correction.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

or a second-order system that yields a 15% overshoot and a settling time of 0.7 seconds, determine he following: Damping Ratio, Natural Frequency, Rise Time, Peak time and the General 2nd Order