There is a beam as shown in the figure below, in which points C, E andG are roller bearings (Roller), point B is hinge bearings (Hinge), andpoints B and F are internal connections (Pin), this beam is subjectedto two forces in total : 1.2 kips/ft uniform live load (Live Load) and 2kips/ft uniform distribution dead load (Dead Load).(b) What is the reaction force of the supports B, C, E and G under thestatic load? A-12²-+-+-B-30CD++84422-EF+84-2HG--++-12--/-22-

Answered: |--12--- B C₁ Jesse -30 -22- E G -2212…

Engineering

Civil Engineering

|--12--- B C₁ Jesse -30 -22- E G -2212 H

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE, that exert uniformly distributed upward loads as shown. Determine the values of wec and WDE corresponding to equilibrium when WA = 750 N/m. 1200 N/m 20 C WBC ADA A 0.6 m- B' 0.8 m The value of WDE is The value of wBc is [ -3.1 ms -6 m- N/m. N/m. D (DE 1.0m E F
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
The cross section is rectangular with a base of 4 in. and height of 5 in. A force of P = 16 kip is acting on the beam. P Part A 4.5 ft- -4.5 ft- 3 ft- Determine the absolute maximum bending stress in the beam, assuming that the support at B exerts a uniformly distributed reaction on the beam. Express your answer to three significant figures and include appropriate units. Omax Value
A rigid bar AB, pinned at end A, is supported by a wire CD and loaded by a force P end B as shown in figure. The wire is made of high- strength steel having modulus of elasticity E= 210 GPa. The diameter of the wire is 5mm. Determine the maximum load P that could be applied so that the vetical displacemt at B will not be more than 6 mm?
5. Shown in the figure is a loaded platform with corresponding rectangular cross section. Determine the maximum tensile and compressive normal stresses at F. (Shear and moment diagram are optional) 1.25 m H 1.0 m 0.5 m A E 250 N 0.75 m 500 N 1.25 m F 1.25 m G 0.75 m B↓ 24 mm TH 60 mm 1
9. A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the figure. The vertical load is always twice of the horizontal load. The collapse load P required for the development of a beam mechanism is P B A Mp K+ 2P 2Mp L с Mp D L
5) A flanged bolt coupling consists of 8 10mm diameter steel bolts evenly spaced around a bolt circle 300mm in diameter and 6 14mm diameter aluminum bolts on a concentric bolt circle of 200mm diameter. Determine the maximum torque that can be applied without exceeding a shearing stress of 50 MPa in the steel bolt and 30 MPa in the aluminum bolts. Use G = 83 GPa for steel and G = 28 GPa for aluminum.
L. Mains A beam ABCDE is 5 m/in length and loaded as shown in Figure Q3. Draw the S.F. and B.M. diagrams for the beam, indicating all major values. Find also the value of the maximum bending stress if the beam section is rectangular 30 mm width by 60 mm depth. 3 kN 10 kNm 1 m B 1m 3 kN/m 640044 Stergat 1 m Figure Q2: Beam Loading 2 m SE
I A vertical steel rod is fixed at the top and supports an 8-kN load at the lower end. The rod is 10 mm in diameter and 25 mm long. Unit weight of steel is 77 kN/m³. What is the total elongation of the rod?
A rectangular beam is supported at both ends. It carries two concentrated load of 10kN, a clockwise moment of 180kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 140GPa. Solve the following if the reaction at point B is 305.2kN, upward. BEAM DIMENSION: Width = 140mm , Height = 360mm NOTE: b = 4.5m What is the numeric value of C1 (1st Constant)? Determine the deflection at midspan.
A laminated plastic beam of square cross section is built up by gluing together three strips, each 20 mm x 60 mm in cross section (see figure). The beam has a total weight of 4 N and is simply supported with span length L = 400 mm. м 20 mm 20 mm 60 mm 20 mm 60 mm Considering the weight of the beam (q) calculate the maximum permissible CCWW moment M that may be placed at the right support. (a) If the allowable shear stress in the glued joints is 0.3 MPa. Round to the nearest tenth. Mmax =| N-m (b) If the allowable bending stress in the plastic is 8 MPa. Round to the nearest hundredth. Mmax N.m
The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. A. Assuming the beam is uniform, which of the following gives the absolute maximum shear? B. What is the value of the absolute maximum moment? C. Reinforcing steel bars [shown by the bold lines] are used in the concrete beam in the lookout as shown in the diagram below, which of the following diagrams best shows the placements of these reinforcements?