On the attached part print, what is the diameter of the part at points "D" and "E"?

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: can you do it in polygon

A: Given vectors : A :  2 kph 45°N of E B :  2.8  kph 58°E of S C :  5.1  kph 28°W of S D : 3.2  kph…

Q: b) Draw Section A-A of the isometric drawing.

A: To draw Section A-A for the given isometric drawing.

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Write the mathematical expression for the Brinell hardness test. HB=2PπDD-D2-d2 Here, Applied load…

Q: is this drawing metric or inch?

A: In the given drawing, the screw size is M8 x 1.25 . That means is it 8 mm nominal size screw. That…

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 18…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: 3.00- 1.25-

A:

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: Draw back the drawing given with the scale 1:1 on the new drawing paper using all the method on…

A: 1. Draw the horizontal reference line using Drafter to a some extent. 2. Draw the vertical…

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: s a caliper use to measure inside diameters widths of slots and the like [a)micrometer (b)outside…

A: To determine the correct option.

Q: 1- Redraw the isometric drawing. 2- Add all center lines. 3- Add all necessary dimensions.

A:

Q: QUESTION 5 Compute Ix (I sub x, in mm“, round-off to 2 decimal places) for the region shown. 4 80 mm…

A:

Q: Draw the front,top and R.H.S/L.H.S view of the given figure attached below.write the processes too…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Circular blanks having following data; Diameter = 35 mm %3D Thickness= 2 mm If the clearance per…

A: Given Data: Diameter of the blank, d=35 mm The thickness of the blank, t=2 mm

Q: The headless type of set screw are known as screws * ....... grub O machine O rag О Сар The only…

A: Isometric drawing is the three-dimensional drawing of the object. It has two types - 1. Isometric…

Q: The figure above shows a section of a vernier protractor. What is the smallest reading (in minutes…

A: i)smallest reading measured that is least count LC=10'5=2'

Q: 1. What thickness limit classifies metal as being sheet? 2. What is the decimal size of 14 AWG…

A: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: 4. WHAT IS THE VOLUME OF THE PART?

A: Given:- Unit:- MMGS Material:- Copper To find:- 1) Volume 2) Mass 3) Center of mass

Q: in 5 minutes please Diameter=38 L

A:

Q: Calculate the angles

A: To find: angles made by forces

Q: 2. Draw a) Sectional Front View and  b) Top View  of the following component.

A: Solution:

Q: The height of an object would be found on which  of the standard views in a set of drawings

A:

Q: Q4 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 1:1.

A: Required Front view, Top view and side view are drawn using first angle method of projections.

Q: What a linear distance would be shown on a drawing if the following dimensions are drawn to the…

A:

Q: Draw figure (3) by using circle, polyline, loft, slice and union.

A:

Q: find the diameter

A: Given : Dimension of a cylindrical side riser   Height= Diameter 25cm×15cm×5 cm steel casting from…

Q: what is the size of the circle (

A: The object is put in the first quadrant in the first angle projection. The item is at the top of…

Q: Question 1: Draw the front view and top view for the given drawing with the dimensions. Use suitable…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Determine the thickness at the end of the plate.

A: For laminar flow over flat plate;Boundary layer thickness at the end of the plateof the length L is…

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 030…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: How do you find the distance if the dimension is 1 5/8 and scale is 3/4= 1 ?

A:

Q: FBD of the figure below.

A: Free-Body diagram A free-body diagram represents the applied load on the section of the beam or…

Q: How did 6650 mm2 come from please show the work.

A:

Q: What is the geometric term that applies to V-groove

A: V - Groove      The general geometry of v groove is two lines for example AB and BC, joined together…

Q: a)Draw the multiviews (Front, Top and Left) of the part given below. b) Show the dimensions of the…

A: According to the details provided in the question, we need to draw three standard View

Q: An equilateral triangle of 35 mm side has an edge in the HP which is inclined at 40° to the VP. The…

A: Projections: it is the representation of point, line, or plane surface on the Horizontal and…

Q: * NOTE: ALL DIMENSIONS ARE IN mm DRAW OETH0GRAFHIC & 1COMETRIC VIEWS.

A:

Q: Q6) For the presented figure: a-What is the accuracy of the vernier caliper. b- What is the value of…

A: A vernier calliper is used for the measurement of the length to an accuracy of 10-4 m. The vernier…

Q: In order to produce the L-Holder shown you must read the dimensions on an Engineering Drawing.…

A: Given:- Engineering drawing of L-holder with dimensions Top view, Front view, Side view, and…

Q: Specify a flatness tolerance of .004 for the top surface of the part in the drawing below. A. B. C.…

A:

Q: What is the name of the part ? What is the part's drawing number ? How many parts are required ?…

A: 1.What is the name of the part? Ans:-FEED HOPPER 2.What is the part's drawing number? Ans:-A-11…

Q: When do the actual dimensions occur?

A: ⇒Actual dimensions occurs when error is zero. ⇒when there is the situation when zero error or…

Q: a) Create a sketch of the Figure 2 as below (.ipt) b) Extrude the sketch in a) by a thickness of 1mm…

A: According to the details provided in the question, we need to DRAW the figure.  i am using the…

Q: If a drawing has 6 fillets with radius (1/2 inch) for imperial units drawing, name one way that you…

A: If a drawing has 6 fillets with a radius (1/2 inch) for imperial units drawing, the one way that we…

Q: e radius of the curve?

A: To determine Radius of curve

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.