On a hot summer day at Tallahassee, FL, the temperature of the outside air is 35oC and the pressure is 103kPa. The relative humidity is 90%. An air conditioner draws in outside air, cools it to 20oC, and delivers it at a rate of 528.5 mol/h. Calculate the rate of moisture condensation (mol/h) and the volumetric flow rate of the air drawn from the outside.

Q: Estimate the one-dimensional heat transfer per unit area through the composite= wall in Figure 1(a).…

A: The heat flow through the plane wall is a direct application of Fourier's law. It states that the…

Q: 3. In a steady-state methane-air flame at approximately atmospheric pressure, the temperature is…

A: Given :Initial temperature Final temperature Concepts used : The adiabatic flame temperature…

Q: Q5- Air at 27°C and 1 atm flows over a flat plate at a speed of 2 m/s. The viscosity of air at 27°C…

A:

Q: Predict which substance in the “specific and latent heat values table “ would require the most heat…

A: We will have to find the highest amount of heat required to raise the temperature of 250 g of the…

Q: The air has a dry ball temperature of 34 °C and a wet bulb temperature of 20 °C is initially heated…

A: Initial DBT of air, T1=340CFinal DBT of air, T2=800CWBT of air=200CDBT of corn kernels,…

Q: Air at a dry ball temperature of 75 ° C and RH 4% is passed over the cooling coil until the air ball…

A:

Q: Name : One side of a plane wall is maintained at 80°C, while the other side is exposed to a…

A: Given that, The inside temperature of the plane wall Tin = 80 oC The temperature of environment T =…

Q: Air at 95°C and 4% RH is passed over the cooling coil so that the air dry ball temperature becomes…

A:

Q: Atmospheric air at 150 C is heated to 600*C and 130 kPa prior entering a heat exchanger. Calculate…

A:

Q: Fruit at 30 ° Celsius contains 5% total solids concentrated via single effect evaporator. Evaporator…

A:

Q: Sample problem A cylindrical iron sample (height to diameter ratio is 2:1) is heated to 97.5°C, then…

A: Given Data:  Given the height to diameter ratio of the cylinder HD =21 Temperature of the cylinder…

Q: A 5 kg solid block is heated at a rate of 400 W by an oven. If the block is initially at 25°C, then…

A: In Chemical Engineering, heat transfer describes the flow of heat due to temperature differences and…

Q: Determine the amount of steam required to heat the product

A: The mass flow rate of the product (m) = 1700 kg/hr Inlet temperature T1 = 20oC  Outlet temperature…

Q: W mᵒC A furnace is wall 300 mm thick is made up of an inner layer of fire brick K=0.80- covered with…

A:

Q: Jutio How much heat is required to raise the temperature of 5 lbm of water from 50°F to 150°F?…

A: Given Mass of water m = 5 lbmInitial temperature T1 = 50 FFinal temperature T2 =150 FSpecific heat…

Q: A 1,1,2-trichloroethane-acetone solution containing 42% acetone by weight at a flow rate of 1200…

A: A mixture of carrier solvent and solute is contacted with the impure solvent (water) to extract the…

Q: Q1) Water at 20 °Cand atmospheric pressure, calculate the heat added in these cases: 1- If the heat…

A: Given,  T = 20°C P = 1atm from steam table; Cp =4.18 KJ/Kg

Q: OHOW much work must be done in order to cool the air in an otherwise empty room of dimensions 5.0 m…

A:

Q: Rich cow's milk (4536 kg/hr, cp = 3.85 kJ/kgK ) at 4.4°C is heated in HE to 54.4°C by hot water. How…

A:

Q: temperature

A: Given: The results of measurement of air temperature obtained a dry ball temperature of 34 oC and a…

Q: Problem 1 Estimate the time required to evaporate 5% of a solid naphthalene sphere (moth ball)…

A:

Q: calculate the feed rate (lb / hr), the speed of the heating steam (lb / hr) and the system economy

A:

Q: Water with mass of 293.07 grams and at 15oC. is heated at constant pressure. the water is completely…

A: for water isCP= 4.187 kJ/kgK, T1=15oC,T2=100oC Q=mCPT2-T1 Q=293.071000×4.187×100-15 KJ Q=104.3 KJ

Q: value of the constant,

A:

Q: (a) Assume that there is a negligible thermal gradient in the wall of the container (dT/dr is…

A: Consider a spherical conatiner is used to store reacting chemicals, whichresults in a uniform heat…

Q: Accetylene gas (C2H2) is often used by plumbers,welders,and glass blowers because it burns in oxygen…

A: Given data:- Acetylene gas is used by plumbers,welders,and glass blowers because it burns in oxygen…

Q: Q3. A bed of ¼ – in. cubes is to be used as a packing for a regenerative heater. The cubes are…

A:

Q: 2. In a nuclear plant, electrical power is generated due to nuclear fission reaction in a reactor. A…

A: Answer  Heat dissipation = 1.3 × 108 W Detailed Solution attached in Step-2.

Q: A student living in a 3.5m x 4m x 2.8m fourth bedroom turns on his 100W fan before leave the room on…

A:

Q: The steady state temperature distribution in a 0.2 m thick wall is known to be T = 250-2750 x²,…

A: thickness, x =0.2 mtemperature distribution, T = 250 - 2750x2 ......(i),......(i)k = 1.163 w/m 0Ca)…

Q: Energy Balances, Costs and Insulation - A 100 meter long section of a steam pipe with an outer…

A: Given: Length of pipe L = 100 m Diameter of  pipe d = 10 cm = 0.1 m Ti = 15oC, Tavg = 120oC, h = 20…

Q: Fruit juice at 25 ° Celsius contains 5% total solids concentrated via single effect evaporator.…

A: The evaporator is the equipment used to concentrate the solids that are present in the solution. The…

Q: 2-13 A certain building wall consists of 6.0 in of concrete [k = 1.2 W/m - °C], 2.0 in of fiberglass…

A: Given, K for concrete = 1.2 W/m°C = 1.2 × 0.5778 Btu/h.ft°F

Q: Which statement is CORRECT regarding green-house gases? O a. Their main sources are from volcanic…

A: The correct option regarding greenhouse gases is to be chosen.

Q: Using specific heat, calculate the change in internal energy (kJ) when 400 kmol of water at 150oC…

A: Given data:  Mole of water = 400 kmol  Initial temperature of water =150C = 423 K  Final temperature…