-Oil 70 cm -Water

Q: What is the volume change in cm´ of a hydraulic oil when subjected to a pressure of magnitude 6 MPa?…

A:

Q: re of water in a pipeline by means of a simple m mercury. The mercury l s 160 mm higher than t ne…

A:

Q: A mercury manometer (density = 13,600 kg/m3 ) is connected to an air duct to measure the pressure…

A:

Q: Convert each temperature. -109 °F to °C (temperature of dry ice)

A: Convert -109°F into °C of dry ice temperature. The following equation is used to convert the given…

Q: What would be the rotation rate (in rad/sec) if during rotation the water in the nght leg (with a…

A:

Q: What is hydrostatic fluid

A: Hydrostatic fluid is the branch of fluid mechanics in which the fluid is at rest in stable…

Q: Convert each temperature. 98.6 °F to K (body temperature)

A: Given: The temperature of the body is T1=98.6 °F The expression to convert the temperature from…

Q: ) Solve for total 5) Solve for the le the water surfa c) What is the ma solved total hy

A: Given

Q: QUESTION 1 The equivalent resultant force is equal to: O -150N O-550N O -400N O -300N QUESTION 2 The…

A: Law of Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the…

Q: A. Draw the F.B.D. of the frame shown in Fig. (4-A).

A: To Draw the FBD of the given loading

Q: Q- A mercury-oil differential manometer measures a 35 cm difference of mercury level. Mercury has…

A:

Q: Convert each temperature. 0.00 K to °F (coldest temperature possible, also known as absolute zero)

A: Given: The temperature is T1=0.00 K. The expression to convert the temperature from Kelvin into…

Q: Q1: Capillary rise in tube depending on the tube diameter, specific volume, dynamic viscosity, and…

A: The Buckingham Pi Theorem states that for an n parameters group, they can be arranged into n-m…

Q: How far below the water surface (in m) should the center of a vertical square 1.5 m on a side with…

A:

Q: 1. Consider the following diagram. The fluid flowing in the pipe is oil (SG = 0.830). The fluid in…

A:

Q: H.W2: two large plate surfaces are 2.4cm. the space between the surface if filled glycerine.what…

A:

Q: Q1: Capillary rise in tube depending on the tube diameter, specific volume, dynamic viscosity, and…

A: Given: The number of variable, n = 5 i.e (h,d,v,µ,σ) The number of independent dimensions, m = 3 (…

Q: Anaerobic treatment is a common treatment process in environmental engineering to degrade organic…

A: Given      Pressure, Pm = 400 kPa

Q: A fluid has specific gravity of 0.9. What is the value of specific weight? (Take g = 10 m/s²) A 900…

A: Specific gravity S = 0.9(Take g = 10 m/s2)To Find-The value of the specific weight.

Q: Give 10 basic question about conversion in pressure units. A sentence form

A:

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

A:

Q: Density of liquid is 850 kg/m Determine relative density and weight density of the liquid.

A: We know the density of liquid is 850 kg/m3, thus we need to figure out the liquid's relative density…

Q: Find the pressure (in lb/in^2) at the bottom of a tower with water 50.0ft deep

A:

Q: Determine pressure due to water at depth of 13 m on a body

A: Given data : Density of water=ρ Depth=h Acceleration due to gravity=g   To find : Pressure

Q: A 15 kg block of wood displaces 6 kg of water  when submerged in water. Bobuoyant force acting on…

A: Write the given data with suitable variables. mb=15 kgmw=6 kgg=9.8 m/s2

Q: 3 12. Determine the absolute pressure at point B if the figure shown below if the density of mercury…

A:

Q: we derive the formula that gives us pressure and deepness in situations that spesific weight changes…

A:

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

A:

Q: Paragraph 8: If 3 Liter of oil has mass of 600 g. The specific weight of the oil is... (1000L 1m')…

A:

Q: An air bubble from the bottom of the sea where temperature is 15°C rises slowly to the water surface…

A:

Q: What is the magnitude and direction of the horizontal component of the resultant hydrostatic force…

A:

Q: Find a) the total force on gate AB in KN and b) the position of the center of pressure in m with…

A: Since the chambers are closed and the pressure in both the chambers must be same. we will transform…

Q: Hand by written ans.Calculate the amount of dissolved oxygen in mg/L in river water at 30°C under…

A: Given, Temperature of the water = T = 30 oC  Absolute value of temperature of water = Ta = 30 + 273…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.