of pin at C is 15mm subjected to single shear. Determine the shear stress in pins A,D and C and the stress in the bar DC if its diamet is 40

Q: combined stresses for the

A:

Q: P W PROB 1. DETERMINE THE と MAXIMUM FORCE THAT CAN BE APPLIED FOR THE BOLTED CONNECTION IF STROBS IS…

A: Disclaimer:As per our guidelines, we will answer the first 3 questions. Resubmit with the particular…

Q: The major and minor principal stresses are 3 MPa and -3MPA respectively. The maximum shear stress at…

A: Given data : Major principal stress=3 MPaMinor principal stress=-3 MPa

Q: Determine stress in rod

A: Given data :   Length (L)=5 mArea (A)=100 mm2Force (F)=10 KN

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Given:P=84 KNd=50 mm

Q: The pins at C and A are in double shear, and the pin at B is in single shear. All pins have a…

A:

Q: 3 650.00 mm 60 kN 650.00 mm 50 kN 650.00 mm B 1,150.00 mm The pin at C has a diameter of 36 mm.…

A:

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Given data: d=50 mmP=66 kN Need to determine the normal stress at point A.

Q: A 120-mm diameter bolt is used in a clevis. Determine the shear stress on the bolt if a load of 350…

A: Given data,  d= 120 mm  F= 350 kN =350000 N

Q: Two blocks of wood are joined together by a rectangular shear key with dimension bx d in mm. If P-75…

A:

Q: Find normal and shearing stresses at point A .

A: For the Normal Stress at pt.A (considering the maximum stress condition) Normal Stress, σx = PA…

Q: Determme the snallest allowable diameter of the solded shuft ABCD, knowng that the allowable shear…

A: Given data as per question Allowable shear stress = 60 Mpa The radius of disc B =80 mm…

Q: Since each of the shafts AB, BC and CD shown in the figure consists of a solid circular bar,…

A:

Q: The lap joint is fastened with four 3/4-inch diameter rivets. a. If the allowable shearing stress of…

A:

Q: Determine the maximum and minimum stress intensities set

A:

Q: The lap joint is fastened with four ¾-inch diameter rivets.  a. If the allowable shearing stress of…

A:

Q: rod A 2m. 2m. 60°

A:

Q: In the figure, when the torture squeezes the material, the maximum force F in the clamping jaws is…

A:

Q: a force q of magnitude 3kips is applied to machine element ab. the uniform thickness of the element…

A: Given data Force (Q) = 3 Kips Thickness (t) = 0.8 in

Q: ss distribution stance. If it yiel s of the yield.

A:

Q: Compute the outer and inner diameter of the hollow circular rod when it is subjected to an axial…

A: Given data as per question Axial pull = 350 KN Allowable stress = 125 N/mm2 Thickness of rod = 10 mm…

Q: D-1 A. solid circulár šhalit öf a the shaft B. the lap joint shown is fastend by three (20 )mm…

A:

Q: Determine the reaction loads and maximum shear stress ! 200 Ibf-in z-in dia. A B 4 in 6 in

A:

Q: a 300 mm 300 mm а F Find the maximum F that can be applied to the lever, if the material has a yield…

A:

Q: QI/ The 15-mm diameter steel bolt is screwed tightly into a block at A. Suppose that the couple…

A: Write the length of the wrench.   L=300 mm=300 mm×1 m1000 mm=0.30 m   Write the displacement of the…

Q: Two horizontal 7.5-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin…

A: Two horizontal 7.5-kip forces are applied to pin B of the assembly shown.A 0.8-in diameter pin is…

Q: Q3 Design the square key which is located on the shaft motor if the diameter of it is (20) mm and…

A: d=20 mm σc=400Nmm2τs=200 Nmm2F=10000N or 10kN Now  Mt=F×d2Mt=10000×.022Mt=100 Nm σc=4Mtdhlτs=2Mtbdl…

Q: In Problem 1, determine the required        diameter of the pin at A if the allowable…

A:

Q: 3- Calculate the total stresses and show the stress profiles in section A-A due to loading F1 and F2…

A: The force at arm in z-direction = F2The force at arm in x-direction = F1

Q: For the given machine part, where the cross-sectional area at m-n is a square with side 5 mm,…

A: The largest allowable value of the distance: e = 11.6667 mm.

Q: Assume that the axial load P = 40KN applied to the lap joint is distributed equally among the three…

A:

Q: 2.) Solve for the normal stress of rod AB with a diameter of 10mm if the block has a mass of 40kgC…

A:

Q: Calculate the shearing stress in pin A of the bulldozer if the total forces acting on the blade are…

A: Two forces acting on the blade is 8K and 4K We can find the shear stress in each pin

Q: The main stress, the maximum shear stress, and the dead angle are obtained when the stress is given…

A:

Q: Q1/ The 15-mm diameter steel bolt is screwed tightly into a block at A. Suppose that the couple…

A:

Q: Figure. rod 2m. 2m. 60

A:

Q: 5 DETERMINE THE WAX FORCE THAT A 12 MMO BOLT CAN HP IF MAXIMUM SAFAR STRESS IS 150 mpa 4. DETERMINE…

A: Given data:Stress,  = 150 MPa = 150 N/mm2Force, P = 180 kN = 180000 NBolt diameter, db = 12 mmTo…

Q: If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the B…

A:

Q: Compute the maximum vertical force F that can be applied at A, if the shearing stress in the pin at…

A:

Q: The lap joint is fastened with four 4/5 in-diameter rivets. The working normal stress for the plates…

A: