If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the B diameter of pin?

Q: what is the value of maximum principal stress in the figure below?

A: Find the maximum principal stress .

Q: Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive…

A:

Q: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube…

A: Given data: F=600 Ndi=25 mmt=5 mm Need to determine the maximum shear stress in the tube.

Q: Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint.…

A:

Q: The pins at C and A are in double shear, and the pin at B is in single shear. All pins have a…

A:

Q: Unit of stress and unit of shear modules is the same.   Select one: True False

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: To build a Tesla car, a machine incorporated with a special tube having a 4mm wall, as shown below,…

A: Given: To find: Average shear stress at A and B

Q: Find shear stress in pin

A: Given data  Given force system

Q: Principal stresses:σ1=31.69 MPa σ2=−30.56 MPa Maximum in−plane stress: σmax=31.69 MPa

A:

Q: A drill drills a hole in a leg of a furniture. Uses a hand-operated drill with a bit of diameter…

A: Given Data Diameter of drill bit is : d=5.79 mm=5.79×10-3 m Resisting torque is : T=0.36 N·m…

Q: BP1: A wire hook is loaded with F=2000 lb. The hook has a wire diameter of 1", eye diameter of 3",…

A:

Q: (D) The pin used at B has an ultimate shear strength of 58 ksi. If a factor of safety of 2.5 is…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: In the clevis shown in Figure 4.3, find the maximum bolt diameter and the minimum thickness of each…

A: Shearing stress is defined as the ratio of load to the shear area. When this shearing stress exceeds…

Q: 03: For the cyclic stress shown in the figure (aside) calculate: 1. The mean stress 2. The range of…

A:

Q: What is the stresses in the rail at 50°C , if there is an expansion allowance of 5 mm per rail .

A: Given data: The temperature of the rail is Tf = 50oC. The expansion allowance is l = 5 mm.

Q: A wooden beam and a steel plate will be attached with three steel bolts. If the plate will be loaded…

A: Given: The magnitude of force P is P=120 kN. The factor of safety is n=3.25. Determine the force…

Q: rod A 2m. 2m. 60°

A:

Q: width of the plates and pin if the load applied is 45 KN. The allowable tensile 180MPA and the…

A: Find the width of the pin by using the below expression. Now substitute the required value in the…

Q: A hook as shown in figure 2 is a symmetrical trapezium of 50 mm deep, the inner width being 60 mm…

A:

Q: why do you multiply by 16 in the shear stress?

A: This question is based on the concept of Torsion equation.

Q: The lap joint shown is fasted by 20mm diameter rivets. Calculate the maximum safe load P that can be…

A:

Q: Suppose the load in the figure below is 2 kN. Further suppose that the distance between the load and…

A: Given : P= 2kN The distance between load and centroid is 1.3 m The horizontal distance between bolt…

Q: In the clevis shown in Fig. 1-11b, the minimum bolt diameter (d=22mm) and the minimum thickness of…

A: Given data  Diameter = 22 mm Thickness = 10 mm Shear stress = 83 MPa Bearing stress = 138MPa Find…

Q: The lap joint shown in Fig. P-126 is fastened by four 4-in.-diameter rivets. Calculate the maximum…

A:

Q: 3. Determine the normal force, shear force, and moment at a section thre ugh point C.Take B 0.1' m…

A:

Q: 31.1 Determine the shear stress in the bolts of a lap joint held by eight 10 mm diameter bolts if…

A: Given data is

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter of this chip…

A: Draw the free-body diagram of the system as shown below, Taking moment about C,…

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

A:

Q: 5 DETERMINE THE WAX FORCE THAT A 12 MMO BOLT CAN HP IF MAXIMUM SAFAR STRESS IS 150 mpa 4. DETERMINE…

A: Given data:Stress,  = 150 MPa = 150 N/mm2Force, P = 180 kN = 180000 NBolt diameter, db = 12 mmTo…

Q: The figure shows a bar with a point load of 22 kN applied at the free end, the other end of the bar…

A: Given data: F=22 kNd=6 mm Need to determine the shear stress in the bolt.

Q: Find normal stresses and shear stress at the given inclination ..using mohr circle

A:

Q: Given a 2m-length rod with 23.0 mm diameter what is the actual stress (in MPa) if axial load is…

A: Given data :- The length of the rod (L) = 2 m                         The diameter of the rod (D) =…

Q: flange bolt coupling is used to connect two solid shaft 125 mm in diameter. If the shearing stress…

A:

Q: for the lap joint shown below, calculate the safe axial tensile fo 126 102 A 220M

A:

Q: Given Ox = -7Mpa, Oy = 3 Mpa y T = 8 Mpa, calculate the greatest principal stress and the maximum…

A:

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A:

Q: Please check attach file

A: In the given problem, firstly, we need to find out the type of loading (axial, bending or torsion)…

Q: Q1/ Find the value of P for the joint shown in the figure if the allowable shear stress is 100 MPa…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.