I need the answer as soon as possible O Determine the offciency and regulation ofODetermine the effe iency and regulation of3-phase,delivering 20mw at o.8 lagging power factorand 66 kv to a balanced Load.Resstan Ce of the line is o.075~/Km150 Km long, 50Hz transmission line1.5 Cm outsite diameter, Spaced equilaterally2m. Use Nominal T method

In this question, Find the efficiency and voltage regulations. Efficiency = PR /Ps ×100 = received…

ODetermine the effleciency and ragulation of 3-phase, 150 Km long, 50H2 trausmission line delivering 20mw at o.8 lagging power factor and 66 kv to a Resistan Ce of the line is o.075~/Km balan Ced Load. 1:5 Cm Outside diameter, Spaced equilaterally 2m. Use Nominal Tmahod

ODetermine the effleciency and ragulation of 3-phase, 150 Km long, 50H2 trausmission line delivering 20mw at o.8 lagging power factor and 66 kv to a Resistan Ce of the line is o.075~/Km balan Ced Load. 1:5 Cm Outside diameter, Spaced equilaterally 2m. Use Nominal Tmahod

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.10MCQ: Transmission line conductance is usually neglected in power system studies. True False

See similar textbooks

Related questions

Q: Three-phase transmission line 90 km long Line impedance z=(0.4+j0.9) ohm/km, If the power Pr=60 MW…

Q: A three-phase power of 460 MW is transmitted to a substation located 500 km from the source of…

A: According to question, find the theoretical three-phase maximum power that can be transferred by the…

Q: 9.33 A three-phase, 60-Hz, 350-km transmission line has the following parameters: R 0.10 /km, XL at…

Q: The resistance and reactance of the single-phase 60Hz transmission line conductors are 7.6 ohm and…

Q: D: A 3 phas e, 50 HZ Transmission line (100km) Long delivers 50 MUA, o.8pf Lagging and 110kv the…

Q: A 230-kV, 100-km, 60-Hz three-phase overhead transmission line with a rated current of 800 A/phase…

A: Given: Transmission line length l=100 km, Total series impedance Z=z·l=0.08+j0.4×100=8+j40 Ω/phase,…

Q: 2) A 200 km long transmission line reactant was given as x=0.25 N / km and shunt admittance as…

Q: O Determine the effeiency and regulation of 3-phase, 150Km long, 50H2 trausmission line delivering…

Q: Q: A 3 phas e, 50 HZ Transmission line (lo0km) delivers 50 MUA, o.8pf Lagging and (aokv), Long the…

Q: Q2. 30, 220 kV, 50 Hz, 115 km long transmission line consisting of three conductors each of 20 mm…

Q: Problem 6- A Three-phase 60 Hz transmission line has its conductors arranged in a triangular…

A: we need to find GMD and radius of conductor to calculate the required parameters.

Q: Q4. A 3-phase, 60 Hz, 500-kV transmission line is 300 km long. The line inductance is 0.97 mH/km per…

Q: electrical engg .fig.shows a single-line diagram of a power system where the generator is connected…

Q: In the power system whose single line diagram is shown below, the line cross-section is 95 mm2, the…

A: we are assuming load voltage KVA and kW ratings are with reference to supply voltage of 10 kVand we…

Q: A bundled 500kv, 60Hz three phase completely transposed overhead line having three ACSR…

A: Consider the area of the bundle conductor is , A=556.5 mm2πr2=556.5r=556.5πr=13.3093 mm Consider the…

Q: A 300 km long 3-phase transmission line of 154 kV is operated at 60 Hz. The line is on average 1200…

A: Given data: f=60 Hz D = 550 cm A=40 mm2 go=30 KV/cm En=1543KV Solution: Area of the conductors,…

Q: a) Assume the line is lossless b) Assume the line has a small loss equivalent to R’ = 1.2 Ω/m

A: Concept: A capacity to do work is called energy and it may exist in potential, kinetic, thermal,…

Q: A ower system is operating at 1000Mw, 132kV, 50Hz, with 0.8 p.f. laging in parallel with another…

Q: 4.41 Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the line…

Q: a short three phase transmission line connected to 33kv 50 hertz generating station at starting and…

A: Write the given information from the question.

Q: Question 1 In the power system network shown in Figurebelowbus 1 is a slack bus with Vi 1.020° per…

A: According to question we need to calculate the value of V21 , and V22.

Q: In the power system whose single line diagram is shown below, the line cross section is 95 mm2, the…

A: we are assuming load voltage KVA and kW ratings are with reference to supply voltage of 10 kV and we…

Q: A 3-phase, 50 Hz, 55 km long overhead line supplies 550 kW at 22 kV, 0.6 p.f. lagging. The line…

A: Here length of transmission line is 55 km so it is short transmission line and hence we can solve…

Q: Q3. A three-phase, 50 Hz, completely transposed 345 kV, 200 km line has two conductors per bundle…

Q: A 530 kV, three phase transmission line with a 350 km length. The series impedance Z =(0.11+j0.72)…

A: Given three phase transmission line with 530 KV ,350 Km lengthSeries impedance…

Q: An energy transmission line with a length of 130 km transmits 150MVA of power at 380 kV voltage. The…

A: Given values are -…

Q: Exercise 15MVA 11kV T2 3 38 j0.15 pu Line (200+j500) N 20MVA AY YA 11kV 25MVA 20MVA Load j0.15 pu…

A: The actual voltage of the synchronous motor is 11 kV Per unit, value is 1.1 pu Then the base voltage…

Q: Supposed a three-phase transmission line is having following parameters. Sending End Voltage, Vs=…

A: We are authorized to answer three subparts at a time. Since you have not mentioned which part you…

Q: A 370 kV, three phase transmission line with a 410 km length. The series impedance Z =(0.45+j0.94)…

A: 370kV, 3 phase transmission line Series and admittance parameters are given. Find. The T and π…

Q: Q1. 30, 110 kV, 50 Hz, 150 km long transmission line consisting of three conductors each of diameter…

A: The solution can be achieved as follows.

Q: A 220-kV, three-phase transmission line is 40 km long. The resistance per phase is 0.15 N per km and…

Q: EXAMPLE : Estimate the distance over which a load of 15000 KW at p.f=0.8 lagging can be delivered by…

A: The solution can be achieved as follows.

Q: For the 3-ph, double circuit O.H.T.L shown below: 1- Find the spacing between the two conductors in…

A: According to the question, 1- Find the spacing between the two conductors in the double-bundle…

Q: EXAMPLE : Estimate the distance over which a load of 15000 KW at p.f=0.8 lagging can be delivered by…

A: Given a three-phase transmission line having, Load power, P = 15000 kW Power factor, cosϕ=0.8…

Q: 3 A 3-phase, 50 Hz transmission line 100 km long, Load current i 5A at 0-9 p.f.lagging and at 110…

Q: Q1. 30, 110 kV, 50 Hz, 150 km long transmission line consisting of three cond diameter and spaced…

A: The solution can be achieved as follows.

Q: S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 /…

A: As per the policy attempting only first question, Given: Vs = VR = 115 Kv

Q: A hypothetical case: A power station generates 50MVA at a voltage of 18.5kV (3-phase, 50HZ). This…

A: A power station generates 50 MVA at a voltage of 18.5 kV (3-phase, 50 Hz). This power must be…

Q: Develop a small-scale equivalent transmission line pi model (per phase) of the transmission lines…

A: Given Conductor spacing = 7.25m P=125MW at 0.85pf lag

Q: A 210 km long three-phase transmission line is operated on a 60 Hz network. Line Finally a 40 MVA…

Q: For the admittance locus shown below, if Vs=10Cos4t Volt. Find the maximum ?power delivered to the…

A: given Vs = 10cos4t Vmax =10 volt P= V2/R =V2*Gmax Pmax = (10)2 * 0.5 = 50 watt

Q: A- A 3-ph, double circi 20 kV, km, 50 Hz has a configuration as shown in the figure below where each…

A: Diameter of conductor=1.35 ft∵1 ft=30.48×10-2 m1.35…

Q: A short 3 phase transmission line, connected to a 33kV, 50 Hz generating station at the sending end…

A: As given in the question

Q: B: A three-phase of 220 kv, 50 Hz transmission line consists of 1.5 cm radius conductor and spaced 2…

Q: 15MVA 11kV T2 3 M jo.15 pu Line (200+j500) 0 20MVA ΔΥ YA 11kV 25MVA 20MVA Load j0.15 pu 12.5/132kV…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: the air-filled two-wire line has a characteristic impedance of 50 Ω and is operated at f = 3GHz…

A: The normalized load impedance is given by ZNL=100+j4050=2+j0.8 In smith chart the intersection point…

Concept explainers

Coulomb’s Law

Coulomb's law states that the attraction or repulsion force between two charged things is proportional to the product of their charges and inversely proportional to the square of their distance. It has an effect along the line that connects the two-point charges.

Question

I need the answer as soon as possible

O Determine the offciency and regulation of
ODetermine the effe iency and regulation of
3-phase,
delivering 20mw at o.8 lagging power factor
and 66 kv to a balanced Load.
Resstan Ce of the line is o.075~/Km
150 Km long, 50Hz transmission line
1.5 Cm outsite diameter, Spaced equilaterally
2m. Use Nominal T method

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
of stion 4 A single phase transmission line is delivering 450 kVA load at 12 kV. Its resistance is 4.5 2 and inductive reactance is 6 2. If the load power factor is 0.9 lagging. Determine the Current through the line Sending end voltage Sending end power factor Regulation of transmission line Efficiency of transmission line A load of 120 MW at a power factor of 0.8 lagging can be delivered by a 3-phase transmission line. The voltage at the intained at 33 kV and the loss in the transmission as 7.5 % of the power delivered. (Consider
(a) A three phase transposed transmission tower comprises of three-bundled conductor and double-circuit configured in vertical position as shown in Figure 2. Each sub-conductor in each circuit and each phase is an ACSR type, size 477,000 cmil and stranding 26/7. Given the GMR of each sub-conductor is 0.8809 cm and diameter is 2.1793 cm, analyze: i. Inductance in mH/km ii. Capacitance in µF/km 0.75m 7.5m b' 4m 4m 45cm Figure 2
A three-phase transposed line is composed of one ACSR Bobolink conductor per phase with a horizontal spacing of 11 meters as shown in the figure. phase with a horizontal spacing of 11 meters as shown in the figure. The conductors have a diameter of 3.625 cm and a RMG of 1.439 cm. Calculate the inductance and capacitance to the neutral of the line.
Problem 3.5: From a 3-phase, 480 V generator switchboard, a feeder takes 3-phase power to two equipment at the other end via cable and trans- former with the combined series impedance Z = 0.04 + j 0.09 Q per phase. The voltage at receiving end point A rises and falls as a large 3-phase, 500 kVA load at point A varies over time. The small 1 kVA load, also connected at point A, remains online continuously, and must accommodate the voltage variations at point A with the 500 kVA load fully on or fully off. Determine the voltage range that the 1 kVA load will see, over which it must perform within its specifications.
A three-phase symmetrical double circuit line is arranged in a horizontal plane as shown in figure below. Calculate and derive an expression for the transposed line for the inductance. Assume balanced equally distributed loads
2. The one-line diagram of a three-phase power system is as shown in the figure below. Impedances are marked in per unit on a 100-MVA, 400-kV base. The load at bus 2 is S2 = 15.93 MW-j33.4 Mvar, and at bus 3 is S3 = 77 MW +j14 Mvar. It is required to hold the voltage at bus 3 at 4006 0 kV. Working in per unit, determine the voltage at buses 2 and 1. V3 j0.5 pu V₂ S₂ j0.4 pu S3
Q1: A 3-phase of sequence ABC transmission line has a conductors of cross section area (82 mm?) and a diameter of (1 cm) as shown in figure below. Delivers a load of 15 MW at 30 kV and power factor of 0.78. Determine the efficiency and voltage regulation of the line. If the line length (65km). The line is completely transposed. For the copper p = 1/58 per meter length. 3 m 4 m 6 m 4 3 m
Problem 1 a- Explain the meaning of the term "bundle conductor transmission line" and discuss the effects of its use on the electrical performance of a high voltage electric transmission line. b- Consider an experimental 1800 kV three phase bundle-conductor line with parameters A= 0.95 and B=j 70. Determine the value of the parameter C of the line. Assume that the line is delivering 2,000 MVA at receiving end whose voltage of 1750 kV and unity power factor. Determine the sending end voltage of the line. d- C- Determine the sending end current of the line.
A 132 kV, 60 Hz double circuit 3-phase overhead line with specific spacing valucs shown in the figure below. The phase sequence is ABC with conductor's radius in 0.74 cm. Assume that the total length of line is 1000 meters. Calculate the following parameters; a) Inductance in H/phase/kilometer. b) The inductive reactance in ohm/km. A B C O20cm O 30cm 40cm 6m 6m
A three phase symmetrical double circuit line is arranged in a horizontal plane as shown in figure below. Calculate and derive an expression for the transposed line for the inductance. Assume balanced equally distributed loads.
Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR