13-Obtain the maximum shear force at span C-D of the given frame. A and B are pinned.Assume that there is a hinge at G.(B-- 18 NP.月D4=6kN/ma=4m, b=3mP=8kN,a žaA.Ba)12 kNb)-18 kN6 KNCevO KNe)3 kNBoş bırak13

Maximum shear force in member CD = -18kN, so correct option is b.

Obtain the nmaximuum shear force at span C-D of the given frame. A and B are pinned. Assume that there is a hinge at G. 13 - (B- 18 kN) P=8kN, q=6kN/m a=4m, b=3m B a) 12 kN b) -18 kN 6 KN Ce O KN e) 3 KN Boş bırak O 0 0 0 0O

Obtain the nmaximuum shear force at span C-D of the given frame. A and B are pinned. Assume that there is a hinge at G. 13 - (B- 18 kN) P=8kN, q=6kN/m a=4m, b=3m B a) 12 kN b) -18 kN 6 KN Ce O KN e) 3 KN Boş bırak O 0 0 0 0O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4-46. If the gap between C and the rigid wall at D is initially 0.15 mm, determine the support…

A: The axial load applied to the structure and due to that the structure deformed then it is axial…

Q: Determine the maximum moment (Ib-ft) in the given structure. Joints A, B and C are pin connected.

A: ∑MB=0-HC×8 + 120×8×4 = 0HC= 480 lb∑MA=012×250×12×6 +120cos30°×8×6.932 + 120sin30°×8×14…

Q: The truss below is loaded on the bottom chord. There is a roller at D and a pin support at I. Draw…

Q: 1. The beam is subjected to a uniform dead load of 1.2 kNim and a single live load of 40 kN.…

Q: etermine the moment at support A of the compound beam. Assume A is fixed a pin, and C is a roller. A…

A: To find moment at point A

Q: 1.0 kN/m 1.2 kN 1.2 kN A 1.2m 2.7m 2.7m 1.2m Determine the internal shear, and bending moment at…

Q: Q1- Calculate the force in member CF of 6 KN the truss. a) 5 KN (T) b) -3.33 KN (C) c) 6 KN (T) d)…

Q: Q.8 P The fixed beam ABhas a hinge MA Cat mid span. A concentrated load Pis applied at C. Whar is…

A: To find the moment MA =

Q: Determine the force in member EB for the truss shown. - 2 m 1.5 m E -2 m F 2 m D B 11 kN 22 kN O…

Q: Q.18 The fixed beam ABhas a hinge MA Cat mid span. A concentrated load Pis applied at C. Whar is the…

Q: The rigid bar AC is supported by a hinge at A and a steel cable BD having a diameter of 12 mm. The…

A: Take moment about A:∑ MA=0F5-FDB3=0FDB=14,4kN

Q: b) Draw influence lines for reaction at support F, member force of members AB, AE and CF. Assume…

A: Note: As the solution for problem (b) has asked, the solution of problem (b) is only provided…

Q: Praw shear force (S.F) and bending moment dingram (B.H). Support A Hinge. E Roller, Pa 20 KN Wa6…

A: Data Given: Asked: Draw SF and BM diagram

Q: Draw the shear and moment d'agram for the frame snown. 3 kif 10 ft 4 klf

Q: Q.10.7 The fixed beam ABhas a hinge MA Cat mid span. A concentrated load Pis applied at C. Whar is…

Q: The compound beam is subjected to a uniform dead load of 1.5 kN/m and a single live load of 10 kN.…

A: i have drawn the ild using Muller Breaslaus principles and then find the maximum positive SF at…

Q: 3:- 5. 22 6 m B on the Beam Solve for the support seoctions at A and

Q: Q.12 P The fixed beam ABhas a hinge MA Cat mid span. A concentrated load Pis applied at C. Whar is…

Q: 2 - Obtain the maximum bending moment at span C-D of the given frame. A and B are pinned. Assume…

Q: 6- Determine the nominal moment strength Mn, if fc' 30 MPa and fy = 350 MPa.

Q: 1- Compute the force in cach member of the loaded cantilever truss by the method of joints. 5M C. 30…

Q: 13- Obtain the maximum shear force at span C-D of the given frame. A and B are pinned. Assume that…

Q: The frame is used to support the wood deck in a res- idential dwelling where the live load is…

A: Given,a=2m, b=4m Live load=1.92kN/m2

Q: Q.2.3 The fixed beam ABhas a hinge MA Cat mid span. A concentrated load Pis applied at C. What is…

Q: 2.) Use cantilever method to compute for the reactions of supports A, B, C and D. Also, draw the…

A: Solution- The given diagram is shown below,

Q: 2. Casz compute the value the Max shear aLong the bea 4 e)

Q: Determine the maximum moment considering only the span where the uniform load is applied. (in kN-m)…

A: From the given diagram we have to calculate the The reaction of the beam after getting a reaction…

Q: wall crane supports

Q: 4-9. Determine the internal normal force, shear force, and bending moment in the beam at point C.…

Q: Determine the area of the moment diagram of the structure w L (WL^3)/6 (-3wL^3)/8 (3wL^3)/8 O…

Q: H.W. Determine the horizontal and vertical comporents of force at pins A and D. 03n 12 KN

A: To find reactions at A and D

Q: 2. A single concentrated live load of 25 kN and a uniform live load of 8 kN/m are placed on the…

Q: Determine the moments at the supports, then draw 2- the moment diagram. Assume B is a roller and A…

Q: Find the force in the member BD 4.0 C 4.0 B 80 kN 150 kN 4.0

A: Consider the section of the truss, Here, T is the tension and C is the compression.

Q: 1.) Use portal method to compute for the reactions of supports A, B, C and D. Also, draw the moment…

Q: A uniform live load of 0.4 k/ft and a single concentrated live force of 6 k are placed on the floor…

A: Solution: Reaction due to uniform Live load. Influence line diagram for SF @ E From Muller…

Q: ermine the bar forces at BE, CE, the truss shown 4 KN 1.2 KN B F. 2.0m H 1.5m 1.5 m 1.5 m 1.5 m 1.2…

Q: 4. Draw the moment diagram for girder IJKL of the building frame. Use the portal method of analysis.…

Q: 11-18. When the 15 kN/m load is applied to the three- member frame the support at D settles 10 mm.…

Q: 3- Replace the distributed loading by an equivalent resultant force, and specify its location on the…

Q: The vertical mast supports the 3.5-kN force F and is constrained by the two fixed cables BC and BD…

A: The tension force is normally the force that is transmitted through a cable when it is pulled…

Q: 9:- 5. 6 m im Solve support seoctions at A and B on the Beam. for the

Q: 1. Determine the internal normal force, shear force, and bending moment in the beam at points C and…

Q: 1.4 A beam is simply supported at A, B, C and D. AB = CD = 8 m, BC = 12 m. Pins are inserted in span…

A: The free body diagram of Beam:

Q: 6 m 6 m B 40 kN

A: The uniformly dead load remains fixed through out the length of the beam and live load can change…

Q: 2. Determinethe internal normal force, shearforce, and bending moment in the beamat points Cand D.…

Q: HW Determine the resultant force at pins A. B, and C on the three-member frame. 200N/m

A: To find force at pins A, B and C

Q: Determine the resultant force at pins A, B, and C on the t tuo d I sit no ool notan sil to…

A: FBD : ∑MA=0-CX×2-CY×2×cot60+200×2sin 60×1sin60=0-CX×2-CY×2×cot60=-533.333 equation…

Q: Obtain the maximum bending moment at member A-C of the given frame. A and B are pinned Assume that…

A: Finding out moment at AC.

Q: Replace the distributed loading with an equivalent resultant force, and specify its location on the…

Question

13-
Obtain the maximum shear force at span C-D of the given frame. A and B are pinned.
Assume that there is a hinge at G.
(B-- 18 N
P.
月D
4=6kN/m
a=4m, b=3m
P=8kN,
a ža
A.
B
a)
12 kN
b)
-18 kN
6 KN
Cev
O KN
e)
3 kN
Boş bırak
13

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1000 N 3000 N 1000 N b ЕЬ 1000 N a F D 30 В 2 m- -2 m- -2 m- -2 m- 4000 N 2000 N Determine the force in member EB of the roof truss shown by method of sections. Indicate whether the member is in tension or compression.
STRUCTURAL THEORY Show complete solution for better understanding Situation 1: From the truss shown, each member has a cross-sectional area of A = 400 mm 2, E = 200 GPa. Use the method of Virtual Work F b.-37.5 C.-30 d. 30 -2m- 1. Determine the stress on member AE a. 37.5 E c. 2 d.3 n B 45 KN 2 m 2. How many zero-force member are there? a. 0 b. 1 3. Determine the vertical deflection of joint E a. 1.42 b. 3.38 c. 2.95 d. 1.24 1.5 m
HW Determine the resultant force at pins A, B, and C on the three-member frame. od sdt no ol noitan 2m Ans: 800 N A, = 61.88 N A, = 569.06 N B = 338.12 N B, = 338.12 N C, = 461.88 N %3D Fc = 572 N FA = 572 N Fg = 478 N 200 N/m %3D %3D 2m %3D %3D Cy = -338.12 N 60 REDMI NOTE 9 PRO B AI QUAD CAMERA
Q/ Determine the forces at the pin joint (F) and the roller support (G) ? 30KN 20 KN Fust 2m B 2m D 2m E 2m
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F- 3190 N, a - 2.8 m, b - 5.6 m, 0 = 43°. B. a D b F Answers: AB - N AC - i N AD - i N BC - i N CD - i N
Q.2// The beam is supported by a pin A and a short link BC. Determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as shown, and each has a diameter of 18mm. -2m Im-
F DE G Ed+d+d+d+d - d - 15 ** The truss is supported by rollers at A and by a pin-joint at G. Find the force in members CD, LD, and KL. Assume d = If the member is in compression, enter a negative force. 1.68 m, F, 3260 N, F, 5480 N, F, 7740 N, F, 5930 N. %3D %3D Enter FCD Answer: Submit All Answers 16. [1 Enter FLD Answer: Submit All Answers 17. Enter F KL Answer: B,
3.75 نقطة )نقاط( السؤال 5 The beam is supported by a pin at A and a short link BC. If P = 5 kN and the diameter of the pin at C is 8 mm, determine the factor of safety against shear stress of pin .C assuming 800 MPa 2P |0.5,m 1 m-1.5 m -1.5 m- 4P 4P P. 0.5 m| 30 B 1.269 1.257 1.322 O 1.462 O
67. A single angle in tension is connected by one leg only. If the areas of connecting and outstanding legs are respectively a and b, then what is the net effective area of the angle? 1sdm b b (a) a- - (b) a+ b. b 1+0.35- a a b (c) a- (d) a+ b 1+0.2- a 1+0.35- b 1+0.2- b a
Find the force in member AB E 4m a. 4kN Tension b. 2kN tension 60⁰ c. 2kN compression d. 4kN Compression 2kN 60⁰ 2kN B 8m 30⁰ 2kN A
A 5m ↓8 40 kN sm C 10 kN 40 1 40 kN 6x5 = 30 m !E 40 kN JF 40 kN 5m F3-3. Determine the force in each member of the truss and state whether it is in tension or compression.
BADLY NEED IN 1HOUR PLS THANKYOU Above is a simple truss with P = 45.67 KN (write answers in kN in 2 decimals) Compute for the forces in: a. Member DA b. Member BH c. Member HI d. Member DG e. Member El f. Member AF g. Resultant Force Reaction of Support F (3 pts)