The wall crane supports a load of 700 Determine the horizontal and vertical components of reaction at the pins at A and D. Also, what is the force in the cable at the winch W? 4 ft-4 ft-4 ft-CB60°700 Ib

Answered: Image /qna-images/answer/810b00db-9227-4318-8187-7c425e83f2d0.jpg

Answered: wall crane supports

Engineering

Civil Engineering

wall crane supports

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The box at B weighs 50-lb. Assume that there is enough friction to prevent slip at B. The plank…

Q: F A m 4 kN 30° 30° E -1 m- E B 4 kN 0 -1 m- 30% 30° -4 kN B 1 m T 2 m D 6 m C

A: Reference : Structural analysis, Truss analysis Given : 2 sets of truss To determine : Indeterminate…

Q: ind. Deterrmine the follow 1. Minimum tension in the parabolic cable

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: Maximum Tension T L2 L1 Angle A The boom is intended to support two vertical loads, F1 and F2. If…

Q: A 600 N B 400 N C E D 150 mm 100 mm-150 mm- 80 mm 100 mm

A: Beam ABCD supported by cables BE and CF

Q: 2. Determine the tension in the cable and the reactions at the hinge. (in tb)

Q: 8) 900 N/m Determine the reactions at the beam supports for the given loading. 400 N/m 1.5 m 0.4 m…

Q: The three-hinged truss arch is subjected to the loading shown. Determine the horizontal and vertical…

Q: A steel girder is part of highway 251A bridge in OK. Inspection reports have indicated that some…

Q: Q2: The homogeneous block shown in figure weighs 1500-Ib. Determine the reactions at A, B, C and D.…

A: Given: A homogeneous block of 1500 lb weight Required: Reaction at A, B,C and D

Q: tension in each segment

Q: PLEASE

Q: Determine the total support reactions at A and B for the truss loaded below. -5 at 3 m- 15 m- 12 kN…

A: To Calculate: Reactions at A and B

Q: (2 DETERMINE THE FORCES IN THE 2 ft CABLES AND BOOM 2 ft BO OA. 3 ft 250 llb

Q: 3. From the given girder shown, it is subjected to a uniform live load of 30 kN/m and a concentrated…

A: Data provided : Uniform live load = 30 KN/M Concentrated load = 120 KN ( of each girder ) To…

Q: The cable AB carries a uniformly varying load. It is connected to a wall at A and is held in…

Q: Ah Av 60° hinge Block Center O of pulley D B 00 By rollers (B₁ = 0) W = 1,000 N (AC BD=1.00 m; CD =…

A: Given:AC=BD=1 mCD=2 mWeight of the block=1000 NSince, beam and pully are weightless.Therefore,We…

Q: Q1) The frame shown below supports 10Olb weight. The cable is attached at A and passes over a smooth…

A: Answer 1) Solution

Q: 13- Obtain the maximum shear force at span C-D of the given frame. A and B are pinned. Assume that…

Q: The three-hinged truss arch is subjected to the loading shown. Determine the horizontal and vertical…

A: Take moment about C∑ MC=0Cy40-240-130-410=0Cy=3.75k

Q: The arch structure is subjected to the loading shown. Determine the horizontal and vertical…

Q: Determine end moment for all member and reaction at the support, and then draw SFD and BMD for frame…

A: Given A frame Required End moment of all member, sfd and bmd.

Q: Given the beam loaded as shown below, determine: (a.)Maximum shear in kN (b.)Maximum moment in kN-m.…

Q: Determine reactions, shear force and bending moment. Draw SFD,BMD

A: Given : Determine reactions and draw the shear force and bending moment diagrams ?

Q: T d + d N d LA F₁ M 17. Enter F cd 18.Enter F ld O 19.Enter F kl B F2 F3 F₁ K C DE dddddd The truss…

Q: : The cable supports the loading shown. Determine the magnitude (Ib) of the horizontal force P so…

A: Find horizontal force P?

Q: 6 KN 53 3m * 5m Find the tension on the cable Find the reaction at c Find the stress in the cable of…

Q: the deck, and therefore transfers half of the load shown to each of the two side girders. Assume the…

Q: Sit-2. Determine the resultant forces at the pins A, B, and C of the three-hinged arched roof truss.

A: FBD :

Q: Maximum Tension T L2 L1 Angle A The boom is intended to support two vertical loads, F1 and F2. If…

Q: A k 9'- 1 kip/ft B 10'- C D 12'

Q: A 4 k 3 k 6 ft 6 ft B 5 k -8 ft-10 ft-10 ft- 15 ft C

Q: E 4 m 1 m 50 kN/m 6 m A B 16 m - 8 m

Q: determine the reactions at pin connection at B

A: Answer Let us draw free body diagram showing forces at B and C as shown below Separate the beam at…

Q: Use the portal method and determine (approximately) the reactions at supports A, B, C, and D

Q: 7he truss shown is supported by a pin (or hinged) at A and roller at B. The truss has a 20 equal…

A: We have to calculate support reactions at A. A is hinged so there will be one horizontal…

Q: Q2. (а) A beam is supported and loaded as shown in Figure Q2(a). Point A is a M UTM pin support and…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

The wall crane supports a load of 700 Determine the horizontal and vertical components of reaction at the pins at A and D. Also, what is the force in the cable at the winch W?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. The structure below is supported by a pin at A and a roller at B. Determine the pin reactions at E, C, and D. 4 F 3'-0" 5000 lb 6'-0" B 2'-0" CH D 8'-0" 6'-0"
Cables, Arches and Influence Lines
Show comp sol Write legibly!
9 ft- Problem 3. The frame that supports the 1000 lb anvil consists of members ABCDE, A 3 t B 1 ft CFG, and DF; the pulley with center G; and the cable. Determine: (a) the forces that pins C, F, and G exert on member CFG; (b) the forces that pins B, C, and D exert on member ABCDE; and (c) the reactions that pin A and roller E exert on member ABCDE. C 3 ft 3 t E
Q3.a
A- In Fig.A, Replace the loading system by an equivalent resultant force and specify where the resultant's line of action intersects the member AB measured from A. B- In Fig.B, A load Q is applied to pulley C, which can roll on cable ACB. The pulley is held in the position shown by a second cable CAD, which passes over pulley A and supports a load P. Knowing that P - 750 N, determine (a) the tension in cable ACB. C- In Fig.C, Determine the components of reaction at B. 1 m 3 m 20 N.m 1m B 25 16 kN D55 12 kN 10 kN 6 m Fig. B Fig.A 800 N-m B 600 N 1.5 m 2 m 1.5 m 2 m 45 Fig. C
For the frame shown, assume that A, B, and C are pin connections. The purlin loads such as D and E are applied perpendicular to the center line of each girder. Determine the horizontal and vertical reactions at the connections A and C of the gable frame. Draw the shear diagram for sloping members and columns. 20 kN 20 kN 40 kN 40 kN EF 30 kN 30 kN G 2.5 m 20 kN kN/m 5 m 3 m 3 m 3 m 3 m- Answer with text and/or attachments:
Draw the moment diagram and determine the forces of girder IJKL of the building frame. Determine the reactions at the base of the columns. Use the PORTAL METHOD OF ANALYSIS.
The cable supports the loading shown. Determine the magnitude (Ib) of the horizontal force P so that xB = 6 ft. XB A 5 ft B P 8 ft 2 ft D 3. 30 lb -3 ft -
Urgent
Cable ABCD supports the loading shown. Determine the tension BC, tension CD and sag of point B (Yb)
The trusses are pin connected and suspended from the parabolic cable. If the structure is pin at B, hinge at A, and roller at C: a. What is the minimum tension of the cable DOE? b. What is the maximum tension of the cable DOE? c. What is the equivalent uniform load the cable is carrying? d. What is the length of cable DOE? Pronda K 50 kN 60 kN 8 @ 6m-48 m 70 kN E 12 m