Observations indicate that an excavator carries an average bucket load of 2.4 LCM per cycle. The soil's load factor is 0.85 and the cycle time averages 0.50 min. Job conditions are rated good and management conditions are rated as fair.

Observations indicate that an excavator carries an average bucket load of 2.4 LCM per cycle. The soil's load factor is 0.85 and the cycle time averages 0.50 min. Job conditions are rated good and management conditions are rated as fair.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Irrigation water with ECi= 2.5 dS/m was used to irrigate a farm with ET= 500 mm per season. It is required to maintain ECeof soil below 4.4 dS/m. Find the leaching fraction? Find the amount of water to be added to a farm of 5 donums and the amount of drainage water.
A truck is hauling earth from a construction site. The truck has the following specifications: Maximum allowable gross vehicle weight 37,800 lb Empty vehicle weight 10,800 lb Heaped capacity 12 yd 10 yd Struck capacity Haul time to dump area, including load, haul, return, and dump times 17 min Delay time 5 min/hr The soil has the following characteristics: Bank density Loose density 110 pcf 100 pcf The productivity, in bank measure (yd/hr), of this operation is most nearly: 38.8 (В) (C) (D) 35.3 32.3 29.5
Will the actual drawdown in the pumping well be more than the theoretical drawdown? If yes, why and what measures can you recommend for reducing the drawdown in the pumping well?
need asap pleaseeee
What is deposition of sediments and how this occur and how can this be managed? (Short essay)
22. Calculate the compacted cubic yards per hour if a com- pactor with a 5-ft drum width travels at 3 miles per hour over a 10-in. lift of aggregate base course with 4 passes required to meet density specifications under average operating conditions.
Q2/ Answer 5 of the followings by choosing the correct answer. 1- The shrinkage in the soil is always accompanied by: A. Increase in the soil density C. Decrease in the volume of soil 2-If the engine with 200hp, consumption factor is: A. 0.7 B. 0.8 C. 0.9 D. 0.6 3-If the contract was assigned according to the traditional method and the employer finds that one of the subcontractors has some errors in his work, it is better here for the employer to: A. Notify the subcontractor of the errors to correct it within time. B. Stop the work of subcontractor to make corrections. B. Decrease in the soil porosity, D. All of the above of diesel is 14.4 lt/hr, and the engine factor is 0.6, then the time C. Notify the main contractor of the error to take the necessary action. D. Making a deduction from the cost according to the size of the error. 4- It is better for a contractor to invest in owning construction equipment when the other option has: A. Better productivity or less time. B. Better…
Discussion: Answer the following questions by referring to relevant References. 1. Zero Air voids line should be plotted with the compaction curve plot? 2. The compaction energy per unit volume (compactive effort) used for the standard proctor test is about 600 kN.m/m³, Prove it? 3. Explain the mechanism behind the shape of the compaction curve?
I will rate, thanks!
The MMDA in its previous study for a proposed sanitary land fill site in Cavite is planning to use a day liner for the landfill. Tests were performed on a sample clay from a borrow site. It was deemed necessary to have a minimum clay liner thickness of 0.30 m. The following results were obtained in the laboratory test Initial water lev! in standpipe... 96 cm. Final water level in standpipe... 56 cm. 12 mm Diameter of standpipe TRA Height of soil sample Diameter of soil sample Duration of test 114 Height of soil sample Diameter of soil sample The project manager would like to datermine the effectiveness of using on-site clay soils for the lining material if it is favorable. Teste were also performed on the on-site clay and the following results were obtained. Volume of water collected.... Constant head. Duration of test 10.2 cm. 5.4 cm. 12 hours. .... 8 cm. 5 cm. 75600 cm³ 60 cm. 1050 hours Compute the permeability of the borrow clay in cm/sec. a) b) Compute the permeability of the…
i need the answer quickly
What is the approximate optimum hourly production rate for a wheeled backhoe filling hauling units? Struck capacity for the bucket is 6 loose cubic feet and the bucket fill factor is 110%,. The cycle time is 2 minutes, the soil type is moist loam with a 25% swell factor.