nt flowing through a radiator at the rate of 3 kg/s are cooled from 105 0C to 81 0 The specific heat capacity of coolant and air are 4.19 kJ/kg K and 1.13 kJ/kJ/K respectively. Th overall heat transfer coefficient from gas to water is 140 W/m2 K. Calculate the surface area required for the radiation if the vehicle speed is 100 km/h. Consider the density of air as 1.225 kg/m3

nt flowing through a radiator at the rate of 3 kg/s are cooled from 105 0C to 81 0 The specific heat capacity of coolant and air are 4.19 kJ/kg K and 1.13 kJ/kJ/K respectively. Th overall heat transfer coefficient from gas to water is 140 W/m2 K. Calculate the surface area required for the radiation if the vehicle speed is 100 km/h. Consider the density of air as 1.225 kg/m3

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.2DP

See similar textbooks

Similar questions

1. Explain how to calculate in-cylinder temperature and the heat release rate dq/d from intake valve closing (IVC) time to exhaust valve opening (EVO) time in 4 stroke gasoline SI engine of 1 cylinder Your answer
Problem 6. Suppose we want to cool an object of temperature A to a temperature of B by submerging it in an environment of temperature To. Use Newton's Law of Cooling to show the time needed to cool the object from temperature A to temperature B is 1 А - То t = In k В -То where k is the cooling constant.
The thermal boundary layer in heat transfer exists whenever there is a difference between the temperatures of the fluid and the outside environment. For fluid flow, how does a boundary layer form?A. Because common surfaces are not smooth, the flow is hindered, and boundary layers are formed.B. The disturbances on the streamlines in high Reynolds number flow produces boundary layer.C. The existence of walls or “boundaries” that keep the fluid inside (or outside) creates the boundary layer.D. Velocity profiles are inherently approaching no-slip condition because of the resistance of the walls.
a) Coolant flowing through a radiator at the rate of 3 kg/s are cooled from 105 0C to 81 0C. The specific heat capacity of coolant and air are 4.19 kJ/kg K and 1.13 kJ/kJ/K respectively. Th overall heat transfer coefficient from gas to water is 140 W/m2 K. Calculate the surface area required for the radiation if the vehicle speed is 100 km/h. Consider the density of air as 1.225 kg/m3
Aluminum To illustrate the effect of ice on the aluminum cooling plate, consider the drawing shown here and the data that it contains. Ignore any limitations due to significant figures. Review lecture example for assistance (Cutnell 377) Ice -10.0 °C -25.0 °C (a) Calculate the heat per second per square meter that is conducted through the ice-aluminum combination. F.0050 m-- (b) Calculate the heat per second per square meter that would be conducted through the aluminum if the ice were not present. Notice how much larger the answer is in (b) as compared to (a). 0.0015 m
Water at 10C temperature flowing from a pipe with a diameter of 100mm at a speed of 2m / s, air from a pressure of 2 ATM at 180F flowing at a speed of 50 ft / s from a pipe with a diameter of 2 in, and an oil with a specific gravity of 0.78 and a diameter of 20 cp at a speed of 5 ft / s through a 2in pipe. Shows the flow state of the biopolymer melt flowing through the pipeline at a speed of 0.2 m/s, with a density of 900 kg/m3 and a density of 1 Pa-s
The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement.Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1, 2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and theblower configuration.following image shows the parameters
A radiant-heating system is installed in the plaster ceiling of a room 36 ft long by 18 ft wide by 9 ft high. Assume direct radiation. The temperature of the concrete floor is maintained at 75°F. The temperature of the air passing through the room is held at 75°F. If the required heat supply to the floor is 8000 BTU/hr, calculate the necessary temperature at the ceiling surface. How much heat is transferred to the air, in BUT/hr? Emissivity of plaster = 0.93; absorptivity of concrete = 0.63. The convective heat-transfer coefficient between the ceiling and the air is given by the equation hc = 0.20 (AT)¹/4.
need some help with this one. The water vapor pressure of ambient air is 19 mmHg, and the wind speed is 1.7 m/s. Calculate the maximum evaporative heat loss (Emax in watts). (Assume skin temperature is 35°C; vapor pressure at 35°C is 42 mmHg., and a standard worker) -53 O 232 O 232 O 30 O -30 O 53
W Determine the heat-transfer rate from an electronic chip whose surface temperature is 31ºC and has an exposed surface area of 2 cm². The temperature of the surrounding air is 22°C. The heat-transfer coefficient for this situation is h = 25 W) and U.S. Customary units (in Btu/h). m². K rate in W (No Response) W rate in Btu/h (No Response) Btu/h What is the R-factor (film resistance, in Km²/W) for this situation? (No Response) K. m²/w Express your answer in both SI units (in
Let's say a 3.0 gram copper wafer is dropped from a height of 50.0 meters. If 60% of the potential energy lost in the drop could be converted to thermal energy used to heat the copper from an initial temperature of 25 degrees celsius, what would the final temperature of the copper wafer? Would the answer be different if the wafer has a mass greater than 3 grams? Note: the specific heat of copper is 387 J/(kg*K). The temperature is between 25.8 and 26.0 degrees celsius, yes the bigger the mass the greater the energy. O The temperature is between 25.6 and 25.8 celsius, answer does not depend on mass. O The temperature is between 25.0 and 25.2 celsius, answer does not depend on mass. O The temperature is 25.5 and of course the more mass something has the greater energy will be needed to raise the temperature. The temperature is 26.2 and if the mass is doubled so will be the change in temperature. O The temperature is 25.9 degrees celsius and the answer does not depend on mass. O The…
3.9 The heat transfer coefficients for the flow of 26.6°C air over a sphere of 1.25 cm in diameter are measured by observing the temperature-time history of a copper ball the same dimension. The temperature of the copper ball was measured by two thermocouples, one located in the center and the other near the surface. The two thermocouples registered, within the accuracy of the recording instruments, the same temperature at any given instant. In one test run, the initial temperature of the ball was 66°C, and the temperature decreased by 7°C in 1.15 min. Calculate the heat transfer coefficient for this case.