a B W b C The solid circular rod has a cross-sectional area of 330 mm2. It is subjected to a uniform axial distributed loading along its length of w = 8 kN/m. Two concentrated loads also act on the rod: P = 2 kN and Q = 3 kN. Determine the normal stress in the rod at x = 1.4 m. Assume a = 0.5 m and b = 1.1 m. Answer: 0 = MPa

a B W b C The solid circular rod has a cross-sectional area of 330 mm2. It is subjected to a uniform axial distributed loading along its length of w = 8 kN/m. Two concentrated loads also act on the rod: P = 2 kN and Q = 3 kN. Determine the normal stress in the rod at x = 1.4 m. Assume a = 0.5 m and b = 1.1 m. Answer: 0 = MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.14P: The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind...

See similar textbooks

Similar questions

Current Attempt in Progress The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is w-70 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot ex t exceed 100 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 140 MPa. Determine the maximum value of Pax that can be supported by the structure. Answer: Pax 3 KN
The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 26 000 psi for the column, and the working bearing stress is 1200 psi for concrete. Find the largest force P that can be applied to the column. Express your answer in Ib. 4 in. 3.5 in. 4/4 7 in.
The solid circular rod has a cross-sectional area of 450 mm². It is subjected to a uniform axial distributed loading along its length of w= 11 kN/m. Two concentrated loads also act on the rod: P = 2 kN and Q = 2 kN. Determine the normal stress in the rod at x = 0.8 m. Assume a = 0.4 m and b = 1.1 m. A →x a Answer: 0 = i B W P -- b MPa
The masonry pier is subjected to the FFF = 810 kNkN load. Consider xx = 0.25 mm and yy = 0.5 mm. Neglect the weight of the pier. Determine the normal stress at corner A. Determine the normal stress at corner B. Determine the normal stress at corner C.
The cylindrical steel column has an outer diameter of 90 mm and inner diameter of 80 mm. The column is separated from the concrete foundation by a square bearing plate with the dimension of 160 mm x 160 mm. The working compressive and tensile stresses are 180 MPa and 200 MPa respectively, while the working bearing stress of concrete is 10 MPa. Find the largest force P that can be applied to the column. Sleel Concrete Foundation Bearing Plane
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
From the figure as shown, determine the stress in psi at the top surface of the second cylinder. Assume the specific weight of the material is 460 Ibf/ft? F = 3000lbf d = 1 ft ww h = 1.5 ft ww
Determine the stress components acting on the inclined plane AB in if: normal stressy = 61MPa shear stressxy = -25 MPa solve the problem using the method of equilibrium. Find normal stress x' =? find shear stress x'y' =?
C-S at E: 40 mm TB The pipe assembly is subjected to the loads shown. Determine the state of 1 kN 30 mm stress at point A on cross-section E and show the results on a volume element. (Ans: 0A = -5.615 MPa, Ta = 5.372 MPa) 0.4 m X 0.3 m B 0.5 m 0.1 m 0.1 m 60" E 0.25 m 2 kN
Determine the stress components acting on the inclined plane AB in if: normal stressy = 61MPa shear stressxy = -25 MPa solve the problem using the method of equilibrium. Find normal stress x' =? find shear stress x'y' =? I have a question regarding the answer you provided. The shear stress is -25MPa. You used a positive 25MPa in the solution. Why is that?
The rectangular bar is connected to the support bracket with a 24-mm-diameter pin. The bar width is w- 85 mm and the bar thickness is 20 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 140 MPa, and the bearing stress in the bracket cannot exceed 130 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax i kN