NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air enters a nozzle steadily at 50 psia, 140°F, and 150 ft/s and leaves at 14.7 psia and 900 ft/s. The heat loss from the nozzle is estimated to be 6.5 Btu/lbm of air flowing. The inlet area of the nozzle is 0.09 ft2. The enthalpy of air at the inlet is h₁ = 143.47 Btu/lbm. Determine the exit area of the nozzle. The exit area of the nozzle is 9 ft²

NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air enters a nozzle steadily at 50 psia, 140°F, and 150 ft/s and leaves at 14.7 psia and 900 ft/s. The heat loss from the nozzle is estimated to be 6.5 Btu/lbm of air flowing. The inlet area of the nozzle is 0.09 ft2. The enthalpy of air at the inlet is h₁ = 143.47 Btu/lbm. Determine the exit area of the nozzle. The exit area of the nozzle is 9 ft²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam enters an adiabatic turbine at the rate of 50 kg/sec. If the steam properties at the inlet are the following: enthalpy = 3520 KJ/kg and velocity = 10 m/sec, at the outlet which is 5 m below the turbine inlet, enthalpy = 2250 kJ/kg and velocity = 275 m/sec, the change in potential energy in kW is nearly equal to?
The mass flow rate of the gas in a gas turbine is 40 kg/s. The specific enthalpy and velocity in the inlet are 1300 kJ/kg and 160 m/s respectively while the outlet are 350 kJ/kg and 50 m/s respectively. Calculate for the work of the turbine if there is a heat loss of 1000 kW. (kW)
Water flows through a horizontal coil heated by steam condensing on the outside. If the inlet pressure and temperature are 2 atm and 160°F (state 1) and at the exit 1 atm and 220°F (state 2), calculate the heat added to the coil per pound mass of water. The entering velocity in 5 ft/s, and the leaving, 500 ft/s. Data: H1=127.9 BTU/lb, H2=1154.4 BTU/lbA. 1031 BTU/lbB. 1042 BTU/lbC. 1048 BTU/lbD. 1052 BTU/lb
A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (i) Find the velocity at the nozzle exit. (ii) If the inlet area is 0.1 m2 and specific volume at inlet is 0.19 m3/kg, find the rate of flow of fluid (iii) If the specific volume at the nozzle exit is 0.5 m3/kg, find the exit area of the nozzle.
(b) Hairdryer is an electromechanical device that blows ambient or hot air over damp hair to speed the evaporation of water to dry the hair. To design a hairdryer, it should contain the following basic components: a duct of constant diameter with a few layers of electric coils, a small fan to pull the air in and force it through the heating coils. If the density of air is 1.18 kg/m³ at the inlet and 0.90 kg/m³ at the exit, calculate the percent increase in the velocity of air as it flows through the dryer.
An air compressor delivers 10 ft3of air at a pressure of 130 psia and 85°F into an air reservoir.Calculate the mass of air delivered (lbm).
A water tube boiler has a capacity of 1000 kg/hr of steam. The factor of evaporation is 1.3, boiler rating is 200%, boiler efficiency is 5%, heating surface area is 0.91 m2/boiler Hp, and the heating value of fuel is 18,400 Kcal/kg. The total coal available in the bunker is 50,000 kg. Determine total number of hours to consume the available fuel.
20°C 101.3 kPa A wind tunnel draws atmospheric air at 2b° C and 1ab kPa by a large fan located near the exit of the tunnel. If the air velocity in the tunnel is 8a m/s, determine the pressure in the tunnel (R=0.287 kPa.m³/kg.K). Wind tunnel 80 m/s Here "a" and "“b" are the last digit of your student number such as 18......37. It means that a=3 and b=7, therefore, temperature is 27 ° C pressure is 137 kPa and air velocity is 87 m/s.
A steam turbine produces 3,100 kW of power. The steam enters the turbine at 10 MPa and 500 C. The steam exits the turbine at a pressure of 30 kPa. The mass flow rate of the steam is 3 kg/s. In the question that follows, select the answer that is closest to the true value. What is the quality at the isentropic exit state (Xes)? 0.947 0.912 0.874 0.829
Air is used as a working substance in a given internal combustion engine, which is supplied with heat at a constant volume. Based on the data, calculate the Pressure and temperature of the ending of isentropic expansion.
A 5-feet diameter Chimney is designed to handle a flue gas produced in a steam power plant at a rate of 17 lb/s. The barometric pressure is 29.92-inch Hg. Outside air enters the combustion chamber at 90 F. The average temperature of the flue gas inside the Chimney is 572 F and its molecular weight is 30. Cv = 0.35, Rair = 53.342 ft-lb/lb-R. Calculate: a. The total draft, feet of air. b. The height of the Chimney, feet
A nozzle is a device for increasing the velocity of a steadily flowing fluid. At the inlet to a certain nozzle the specific enthalpy of the fluid is 3045 kJ/kg and the velocity is 70 m/s. At the exit from the nozzle specific enthalpy is 2850 kJ/kg. The nozzle is horizontal and there is a negligible heat loss from it. Determine; e. 1. The velocity of the fluid at exit The rate of flow of fluid when the inlet area is 0.1 m? and the specific volume at inlet is 0.19 m/kg. ii. The exit area of the nozzle when the specific volume at the nozzle exit is 0.5 m'/kg. 11.