Please help me answer this one, complete solution with free body diagram please thank you. Problem Number 2: In The given cable carrying concentrated loads W,V & A, determine the maximum tension in thecable system and the diameter of the cable if it's capacity is 275 MPa and the total length of the cable.45 mED30 m35 mGW = 450 KN10 mA = 550 KN30 m75 m50 m30 mV = 375 KN

Answered: Image /qna-images/answer/53790e33-300d-4f84-acaf-e8fa9bd870d0.jpg

Answered: nd the total length of the cable.

Engineering

Civil Engineering

nd the total length of the cable.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Under conditions of unsaturated water flow in soils, water is moving: mainly or entirely in macropor...

A: Option 2 is correct Mainly or entirely in micropores

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1)...

Q: 8. The composite bar is stress-free before the axial loads P1 and P2 are applied. Assuming that the ...

Q: 1) At the instant the valve is opened, the Venturi meter indicates a pressure difference of 735 kPa....

A: step 1-

Q: Tne dehectonat the end ot the hollow steel tube shown The outside diameter of the sicel tubeis 8 Inc...

Q: A reinforced concrete column 200 mm in diameter is designed to carry an axial 3 ft 6 ft 1 ft compres...

A: Given:

Q: A wooden piece having a width of 10.20 inches. Available moisture content of this piece is found to ...

Q: If a bus traveling at 42 m/s is subjected to a steady deceleration of 7m/s? . How long will it take ...

A: Given data : The value of deceleration a=-7 m/s2 The value of initial velocity U=42 m/s The value o...

Q: Cross-sectional influence diagrams (N, T, M) of the carrier system whose loading status is given in ...

A: The s=diagram of the above equation is now we have to resolved it with the help of equilibrium equ...

Q: A tank has a hole in the bottom with a cross-sectional area of 0.0025 m and an inlet line on the sid...

A: Given Data -

Q: At the wilting point, the matric potential in bars is generally considered to be: O -31 -1/3 -11 -15

A: The permanent wilting point is the point when there is no water available to the plant. The permanen...

Q: The truss is used to support the loading shown. Determine the required cross-sectional area of membe...

Q: A rigid container is partly filled with a liquid at 1520 kPa. The volume of the liquid is 1232 liter...

A: Given,At P1=1520 kPaThe volume of the liquid is,V1=1232 litersAt P2=3039 kPaThe volume of the liquid...

Q: A beam ABCD with a vertical arm CE issupported as a simple beam at A and D (see figure).A cable pass...

A: Given:- tension force=1800lb To find:- (a) Draw the shear-force and bending-momentdiagrams for beam...

Q: A runner with mass 100 kg run at speed 25km/h on a wet road with friction force equal to : O 245.2 N...

A: Friction : Friction is the force that keeps solid surfaces, fluid layers, and material elements movi...

Q: AbjusT THE QUA DRILATERAL USING SNGLE coveTION ALD SIDE tonpITION EQUKTYOH. ANCLE OBSERVED ANGLE 81 ...

A: After the Fieldwork of measurements of angles, there is a need for adjustment of angles. The angle m...

Q: A two lane national highway without raised kerb is passing through a plain terrain. Calculate the le...

Q: How many slope deflection equations are created for a beam with 6 spans? Group of answer choices a) ...

Q: The concrete pier (E=29 GPa) is reinforced by four steel rods (E=200 GPa). If the pier is subjected ...

A: Given Data -

Q: Find the member forces and reactions for the truss with loading shown.

A: Given - To find - Find the member forces and reactions for the truss with loading shown.

Q: V el. 260.3 ft alig h SH 100 olig a Scale (ft) Reservoir si 1ote Concrete spillway Sheet pile el. 18...

A: Computing for the top figure From the above figure, given d...

Q: A simply supported beam is subjected to a shear force of 40 kN. Determine the maximum shearing stres...

Q: 2. Solve Prob. 1 if the points of application of the 6000-lb and the 4000-lb forces are interchanged...

Q: What is the slope in a fixed support with a settlement of 1 mm? O undefined O 0.5 O1

A: Answer : slope will be zero at fixed support. Option (c) 0. Is correct.

Q: . Draw the shear and moment diagrams for the frame. Partial answer: Dy = 92.97 kN (up) 150 kN C 10 m...

A: Given -

Q: 1. A cylindrical pressure vessel is fabricated from steel plates which have a thickness of 20 mm. Th...

Q: MY QUESTION IS WHY IS IT 4 ON THE UNDERLINED ONE?? I DON'T UNDERSTAND

A: Since the perpendicular distance of RBH and RBV from point A is 1.2 m each, hence moment about A s...

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B . (Figure 1...

A: Given: Tallow = 70 MPa We have to calculate the maximum value of P

Q: Force Reactions on a Structure 1 A cable supports an L-shaped beam subjected to a uniformly distribu...

A: ASKED: To determine: tension in the cable, T x-component of reaction at A, RAx y-component of react...

Q: 2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as s...

A: Given: The value of P is 3100 lb. The area of rod is 0.52 in2. The expression for stress is given ...

Q: O 375.1 m

A: Given:- 160,000 sq. ft. angle of elevation of the three flag staffs=45o,60o,60o To find:- height of ...

Q: In checking the density of an earth filled dam 15kg of wet soil with a specific gravity of 2.6 were ...

Q: What is the length the PRN code for the GPS C/A code signal? How much is that in metres?

A: Pseudorandom noise (PRN) codes are an important element of code division multiple access (CDMA) base...

Q: The cross-sectional dimensions of a beam are shown in the figure. (a) If the bending stress at point...

Q: An 2014 T-6 aluminium flag pole with a hollow rectangular section experiences a wind force of 750 N ...

Q: The composite bar is stress-free before the axial loads P1 and P2 are applied. Assuming that the wal...

Q: Prob. 4.3-1. A bimetallic torsion bar consists of a steel core (G, = 75 GPa) of diameter d, = 25 mm ...

Q: 4.7.2 (This problem is adapted from the Ground Water Manual.") Drawdown versus time data for an obse...

A: In this question we use Theis euqation Theis equation depicts radial limited groundwater flow in an ...

Q: 2.5 ft, 2.5 ft, 5 t Rax 20 lb 40 lb Ray Rbx Rby Cx Су 10 ft Dx Dy Ex mn. Both rollers Ey 4- D.

Q: A flat plate 2 m long and 1.5 m wide is towed at 25 km/h in water. The drag and lift coefficients ar...

Q: Problem 3. Member ABC is supported by cable CD and a square collar at A that fits loosely over the s...

A: CALCULATIONS of tension in Cable CD###

Q: Determine the support reactions of the following truss using the method of joints. Specificy any zer...

A: Given- To find - Determine the support reactions of the following truss using the method of joints...

Q: Problem 1. For the beam and loading shown. a. Determine the distance x for which the maximum absolut...

A: Given,

Q: For the beam and loading shown determine the max required width b knowing that for the grade of timb...

Q: What is the total flow rate of the given figure if the channel slope is 0.17° and n =0.012? Use Kutt...

Q: A 45 kg boy whose leg bones are 5 cm? in area and 50 cm long falls through a height of 2 m without b...

Q: DETERMINE THE HORIZONTAL DEFLECTION AT C. USING CASTIGLIANO'S THEOREM. EI IS CONSTANT

Q: A rectangular flume 3m wide and 1.5 m deep has a carrying capacity of 45 cu. m/s. 1f the same materi...

A: Given data in question Rectangular channel Discharge Depth Width Trapezoidal channel made of same ...

Q: 5) The walkway ABC of the footbridge is stiffened by adding the cable ADC and the short post of leng...

Q: For the given loading, determine the zero-force members in the truss shown. Fig. P6.33

A: Truss : A truss is a rigid structure made up of elements such as beams that are joined by nodes. A t...

Question

Please help me answer this one, complete solution with free body diagram please thank you.

Problem Number 2: In The given cable carrying concentrated loads W,V & A, determine the maximum tension in the
cable system and the diameter of the cable if it's capacity is 275 MPa and the total length of the cable.
45 m
E
D
30 m
35 m
G
W = 450 KN
10 m
A = 550 KN
30 m
75 m
50 m
30 m
V = 375 KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the tension in each cables, sag Yc and the largest mass (M) that can be sustained by the cable if the maximum tension allowed is 650 N 3.75 m 1.5 m 1.5 m A 0.75 m Yc 5 m E F 38 kg Mass (M) 1. What is the largest mass (M) that can be sustained 2. Which cable is the maximum tension located 3. What is the tension in cable CD 4. What is the value of sag Yc
Question 1 Cylinder E has a mass of 80 kg and each cable segment can sustain a maximum tension of 200 N, determine the largest mass of cylinder F that can be supported. Also, what is the sag yc? -15m 1.5 2 m 2 m 1 m 2 m Ус D B E F
A 2-meter timber post is kept in a vertical position by three guy cables as shown. 1.5 m Z B 0.4 m C y 1.8 m X D 1.4 m 2. If the tension on cable AD is known to be 275N, which of the following is closest to the magnitude of its component along the x-direction? 200 N 222 N 155 N 44.4 N + the following is closest to the magnitude of the tension on cable AC if its components along the x, y, and z directions are 35N, 1731 ctively?
Problem 3-A uniform rod of weight W bears on a horizontal surface. What is the value of & for which motion is impending? What is the corresponding tension in cable BC? -FC B L Ms=0.33 A L
Situation 6: Z-axis Three tension cables as shown on the figure are acting on a vertical post to remain its position at E. If the tension in cable AC is 4 N, determine the tension developed in the other cable so that the resultant at A X-axis y-axis will be vertical. sourcowa eHeocom 1 m m 4 m D
For the cable shown below,Determine the tension segment CD in kNDetermine the tension segment AB in kNWhat is the value of h?
The tension in cable BH is 20.60kN. Determine the vector expression for the tension acting on H. (H=Hxi+Hyj+Hzk)
8) A shaft of diameter (d = 5-mm) is to be puled through a (4.5)-cm-diameter glycerin-filled sleeve as shown in Figure. The glycerin to be used has a dynamic viscosity of 1.5 Pa.s, and the cable is pulled by 60-N tensile farce. If the cable is to be pulied at a velocity of 0.02 m/s and the velocity profile equation though glycerin is (u = 0.6y + 20y), what is the length of the sleeve that can be used to provide this velocity? Assume that the cable can be kept at the center of the sleeve. Seve Shaft
The sign has a mass of 100kg with center of mass at G . A pole is supported by ball- and -socket joint at A and by two cables. Shown in below image 1- Express the unknown cable tensions as Cartesian vectors2- Express the equilibrium equations in cable tensions and reaction at A3- find the magnitude of two tensions and the vector notation of reaction at A
A vertical pole is subjected to a pull of 620N in the yz plane and 15 deg below the horizontal. The guy wires AB and AC are attached to supports in the xy plane. The pole rests in a socket. What is the tension in each cable?
Problem 5.1 Coplanar Force Systems A ball is suspended using cables AB and AC, and a force is applied at A in a horizontal direction. The ball D has a mass of 35 kg. If a force of F 135 N is applied to the ring at A, you are required to: a) Determine the dimension d so that the force in cable AC is zero. 1.5 m d B -2 m STRINGER STRAKE CONNECTION SEAM SHELL OR NOUTENPLATING M STANCHON D TRAPE ma GE HEEL BOTTOM PLATING TRANSVERSE FRAME LOTION ITUDINAL STRAKE
Problem A For the cable system ABCDE loaded as shown below, determine (a) the magnitude of the vertical force P applied at D, (b) the vertical distance yc and (c) the tension in each cable segment. Assume that the weight of the cable is negligible. 9.5 m A 4 m 12.5 m В' 4 m 14 kN Ус C 4 m 6 kN 7.5 m D P 4 m 441