The cross-sectional dimensions of a beam are shown in the figure. (a) If the bending stress at point K is 35 MPa (C), determine the internal bending moment Mz acting about the z centroidal axis of the beam. (b) Determine the bending stress at point H. The bending stress is positive if in tension and negative if in compression. 85 mm 4 mm TT K 55 mm H 4 mm 45 mm 4 mm Arswers: (a) Mz = UN-m (b) OH = JMPA

The cross-sectional dimensions of a beam are shown in the figure. (a) If the bending stress at point K is 35 MPa (C), determine the internal bending moment Mz acting about the z centroidal axis of the beam. (b) Determine the bending stress at point H. The bending stress is positive if in tension and negative if in compression. 85 mm 4 mm TT K 55 mm H 4 mm 45 mm 4 mm Arswers: (a) Mz = UN-m (b) OH = JMPA

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers with cach being 6 mm thick and brazed to a centre steel layer of 5 mm thickness as shown in Figure Q3. An axial tensile force of P- 37 kN is applied to the assembly by means of a rigid end cap at B. Given that the assembly is fixed at end A and the Young's modulus of aluminium and steel are E.= 70 GPa, Es= 200 GPa, respectively, determine: i Whether this structural configuration is statically determinate or statically indeterminate, and clearly explain your reasoning. ii. The normal forces in the aluminium layers and the steel layer i. The normal stress in the aluminium layers and the steel layer. State whether the stresses are in tension or compression iv. Determine the deformation of the assembly Cross section of the bar 6 mm 5 mm 6 mm 30 mm 260 mun Aluminium. Steel- Aluminitum Nא 37 30 mm
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar B3 in kN. 35KN В1 B2 B3 10KN 15KN 30KN
QUESTION 2 A steel cantilever beam is made of two structural tee- section beams welded together as shown in the Figure 2 below. Determine the allowable safe load (P) that the beam can carry. The allowable stresses are: 0-150MPa in tension and compression, T=100MPa in shear, and q=2000N/mm on the welded joint. 150 -200mm- -150- 25 weld 25 ΝΑ 25 M=P V=P -1.0m- Figure 2 weld 0.5m 31
The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 60 kip is applied to ring F and the allowable stress of the material is 67 ksi, determine the cross-sectional area of each rod and the horizontal displacement of point F. B AAB = a in² AL 6 ft E 1 ft2 ft- AEF=2a in² 2 ft FO 60 kip D ACD = 1.5a in² C
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar Bị in kN. 35KN В1 B2 ВЗ ... 10KN 15KN 30KN Determine the axial load acting on bar B2 in kN. Determine the axial load acting on bar B3 in kN. Determine the axial stress of bar B1 in MPa. Determine the axial stress of bar B2 in MPa. Determine the axial stress of bar B3 in MPa. Determine the total deformation of the bars B1, B2 and B3 in mm. Determine the deformation of the bar B in mm. Determine the deformation of the bar B2 in mm. Determine the deformation of the bar Bz in mm. 35 А 35 B 20 10
Q1/ A thin-walled cantilever has a constant cross-section of uniform thickness with the dimensions shown in Figure. It is subjected to a system of point loads acting in the planes of the walls of the section in the directions shown. Calculate the direct stresses according to the basic theory of bending at the points 1,2 and 3 of the cross-section at the built-in end along the beam. 50N 2 mm 50 N 80N 2 mm 100 mm 2 36 mm 80 mm 24 mm
A ruler is clamped at 0.36 ку = weight weight is at deflection at deflection at It is What are ruler as x=17cm uniform bean a x = 3cm and x = 30cm x=16cm is x = 20cm is 1.5mm Inn the value functions for modelling the beam? (length, load, boundary Conditions • Estimate the flexural rigidity of the ruler.
The rigid bar DEF is welded at point D to the uniform steel beam AB. For the loading shown, in Figure I determine (a) the equation of the elastic curve of the beam, (b) the deflection at the midpoint C of the beam. Use E =29 x10° psi
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the loadP = 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa C. Aluminum L=2m A=500mm2 2m 2m E-72Mра P=20KN
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa Aluminum L=2m A=500mm 2m 2m E-72Mра P=20KN
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP