Name (Chinese), Q1 a) Calculate the reactions at the supports A and E. b) Draw the shear force diagram. e) Draw the bending moment diagram. d) Draw the deflected shape. 15kN 15kN/m Hinge 2m 4m 2m 3m 10kNm

Q: Determine the equation of the influence line for the reaction at A in the continuous beam shown in…

A: By Muller Breslau method, As we have to find the reaction at end A, hence Support at A will be…

Q: How is ThOD solved?

A: THOD  Theoretical oxygen demand (ThOD) is the calculated amount of oxygen required to oxidize a…

Q: What is this called?

A: Chisel

Q: Sketch SFD and BMD in terms of w and P

A:

Q: Define The required diameter

A: A diameter is a chord that runs through centre point of circle. The centre of circle is at midpoint…

Q: 5. Find diameter y. All dimensions are in millimeters. 1 + 19.30 DIA 118.00 -३०

A: Tapered beam with larger diameter at AB = 19.3 mm  Length of beam ,L = 118 mm  Tapered angle = 3°…

Q: F & H are incorrect

A: As per question requirment we only find out f and h here. Find out -  (f) Length of Curve (h)…

Q: Question 2 Problem No.2 A T-beam as shown is reinforced by 8-25mm diameter bars. Assuming…

A: solution: Given: fc=4000psi; fy=60 psi b= 400mm; bw=250mm; d = 100+250-75 = 275mm As=8π4252=3926.9…

Q: Quiz #1 Problem 1: Prove the following relationship. Gs Y. (1+ Mc) Y =- 1+e

A:

Q: answer in 4 decimal places

A:

Q: A thin circular rod is supported in a vertical plane by a bracket at A. Attached to the bracket and…

A: Given data: R=12 in=1 ft. K= 3 lb/ft

Q: Determine the ỹ coordinate. y b. = ky? a

A:

Q: Discuss Shape Factors

A: Shape factor:- Shape factor is defined as the ratio of plastic moment and the yield moment of the…

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: Fo B - P 800 mm C -600 mm

A:

Q: 7⁄8 inch+  5⁄32 inch

A:

Q: Describe briefly the T-v Diagram.

A: The TV diagram refers to the Temperature-Volume diagram for a particular substance. The diagram…

Q: The A-36 Steel member W8x31 shown below is to be used as a pin connected column. Determine the…

A: Given :- A-36 steel member W 8×31 is given  Pin connect column is used Cross sectional area A = 9.13…

Q: Give real life examples of Mohr's Circle

A: Brief concept introduction- Mohr's Circle- It gives the relationship between the normal and shear…

Q: Determine y for the area shown y 1" 1" in .5" 1" 2" 2" X

A:

Q: 1⁄6 yard +3⁄8 yard

A:

Q: Use the principle of virtual work to calculate the vertical displacements at the quarter-and…

A: Draw free body diagram Consider the summation of forces in the vertical direction…

Q: usescale (1/1) draw the front Section view in mides pan and the side Sectional Vien middles pan for…

A: Front Sectional View: The front sectional view is the view of the object done by taking a section…

Q: According to this figure, What is d? What is dt?

A: Draw the figure.

Q: Calculate external as well as total indeterminacy

A:

Q: Determine degree of total indeterminacy

A: Given data : The given structure is truss structure . It is pin connected carrying tension or…

Q: wrong given, pls. answer

A: Given: Span= 10m, axle loads as shown in figure

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: 1) Determine the area of the shape below. -130.0- 100.0 -160.0-

A: The above figure is the trapezoid  The area of the trapezoid = sum of the parallel…

Q: 31⁄5 / 4⁄7

A: 31/5=6.2 4/7=0.571

Q: hat about pin d?

A: We know that Forces acting at Joint D are shown in figure below Forces moving away from joints are…

Q: Explain any fiften (15) AUTOCAD commands used in drawing

A: Autocad is a computer based drawing software which is in the field of civil engineering to prepare…

Q: For the following items, answer whether the multiview projection matches the isometric drawing depic…

A: The given figure shows the different items, it is required to state whether the Multiview projection…

Q: Use the CAD drawing below and determine distances A and B to the nearest hundredth inch. + 2 A = O O…

A:

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: What is CALINE3 model?

A: Solution: CALINE3 model is considered as the dispersion model that is used for predicting air…

Q: You are appointed as an officer of Occupational Safety to investigate the incident happened during…

A: Officer of Occupational Safety is responsible for 1) Enforcing safety policies, 2) Conducting audits…

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.