MCQ/ If Ø = 0.987643 rad. Find Ø in degrees. A-56º 35' 16'' B-45º 42' 16'' C-52º 04' 26'' D-54º 30' 16'' E-35º 25' 25'' F-65º 25' 13''

Q: There is a table of an observed plane triangle ABC but some parts are missing. Please fill up the…

A: Given- |Angle| Observed Angle| Weight|  A 58°07°04" 4 B 61°16'55” 3 C 60°41'39” 2 we  have to find…

Q: 158.550 5.765 0.345 155.630 1.100 0.465 1.255 154.995 2.095 BM 36 0.130 153.030 0.245 BM 35 154.375

A:

Q: 4/ The following is an incomplete page of level book in which X indicates missing Entry line.…

A: Using rise and fall method

Q: A railroad curve has De = 4°00', I = 24°00', and PI station = 35+45.00 ft. Use the chord definition…

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: 30 20 30 10 20 200 160 170 170 190 170 180 180 he least count or fineness of reading for this…

A: A theodolite consists of 2 vernier scales, Vernier A and Vernier B,  For less important works Only…

Q: ► Numerical problems 3: QI//calculate the horizontal length of the line measured as follows:…

A: The given data is: Bay Inclined Length (m) Difference in level between end of bay (m) 1 29.634…

Q: Determine the characteristic of Log (1020.20) O 1020 0 0.20 O 20

A: Integer part is characteristics

Q: Lloukle Inte gr ation Meth od Lletermine the ff :). LDefle etion at e). Mope at C

A:

Q: Find the value of e (degree) if coversed sin 0 = 0.256855 O 43.07 O None of these O 48.00 O 14.88 O…

A: To determine the value of θ for given coversed sine value.   Given, Coversed sinθ=0.256855   The…

Q: -300 200 4S 30k 30 30 E =? Ey=? Y. E,=? Eg=? Bq =? つ V.

A: Strain is given in different orientation 1st we have to resolve these into x and y direction.

Q: + Compute for the unknown Line AB BC CD DE EA LINE AB BC CD DE EA Distance 300 400 250 350 277.96…

A:

Q: Course: Civil Engineering Subject: Integral Calculus Topic: Definite Integral   Integrate and find…

A: Step 1:Step 2: Step 3: Step 4: Step  5: Step 6: Step 7: Step 8: Step 9: Step 10: Step 11: Step 12:…

Q: 1. Complete the differential level notes shown below, perform the customary arithmetic check,…

A: Leveling is the process in which we measure the levels of the various point of field in a linear or…

Q: 1. Complete the differential level notes shown below, perform the customary arithmetic check,…

A: Formulas Used: 1.Mean Rdg= (Upper + Middle + Lower ) Rdg/ 3  2.S = (Upper - Lower) Rdg  3. H.I =…

Q: What are the values of X, and Y of the table below using the storage-indication method and equation…

A:

Q: Use the following values for your calculations: width of channel, b = 36 cm; roughness, n = 0.01. 1.…

A: Note: As per our policy for a multipart question only three parts can be solved for other parts…

Q: Calculate the coordinates of a foresight point P101 using the following data: Occupied point O: N…

A: Point O BS=0.45 m HI=144 m FS=- Elevation=143.55 m Azimuth=285 degree Distance=35.3 m Point A BS=-…

Q: Find the area of a piece of land FGH, knowing that FH=150 m. Left hand face Right hand face Occupied…

A: To Determine Area of triangle FGH

Q: Draw the following figure in AutoCAD and extract the value of the area of the triangle ABC using the…

A: To Determine Draw the given figure and Area of the triangle ABC using area Command in AutoCAD.

Q: The data in the table below is for a closed-polygon traverse. Course Azimuth Length (m) Interior…

A: The data in the table below s for a closed-polygon traverse. Course| Azimuth [Length (m)| Interior…

Q: when e/D is 0.00025 what is reynold numbe

A:

Q: Q.2. check. If there is an error please distribute it to the elevations. E = 40* K Please calculate…

A: Levelling is the procedure of comparing heights of points on the surface of earth. It is important…

Q: Q3: The polygon traverse ABCDEA shown in figure 2. is to be divided into two equal areas by a…

A: If polygon vertices are(x1,y1), (x2,y2), ............... (xn,yn)then areaA =…

Q: A. What is the Elevation of BM2? B. What is the Elevation of BM3? C. What is the Elevation of BM4?

A:

Q: -100 80 A3 200 1. What is the value of ybar from the 1-1 line ( Select] 2. What is the value of…

A:

Q: A plank L m long is placed in a horizontal position with its ends resting on two inclined planes as…

A: Given: Required: How close the load P can be placed near B before slipping impends

Q: 1) choices: 49.81 62.59 59.62 52.69 2) choices: 42315487 mm^4 34643447 mm^4 31534337 mm^4 31943887…

A:

Q: Find the elevation of point A given in the figure below.

A: Contour lines are the lines that drawn by joining lines of equal elevation. The elevation of A will…

Q: 2. The discrepancy for the measurement is the difference between the first measurement and the…

A: Given Data:

Q: The following is a page of an old level field book, in which some of the missing entries are shown.…

A:

Q: Determine M, if f, = 420 MPa and f'c = 28 MPa. %3D 75 75 75 75 mm mm mm mm 150 mm 75 mm 75 mm 825 mm…

A:

Q: The log is being towed by two tractors A and B. Determine the magnitudes of the two towing forces FA…

A: Given :

Q: Compute the unadjusted departures.

A: Answer  We know that Departure is given by Lsinθ  (positive for East and Negative for West) Latitude…

Q: Do not include the unit in writing the answer. Express all values up to 3 decimal places. You can…

A: Complete the table above?

Q: STA BS HI FS IFS ELEV BM25 5.3650 259.5108 254.1458 0+ 000 2.3225 257.1883 2+ 000 1.3256 258.1852 4…

A: Given profile levelling Height of instrument = elevation+ BS Elevation = HI - FS/IS

Q: Example 5: The followings are the F.B. of lines. Calculate their B.B. (1) AB N 18° 0' E 1 (2) BC S…

A:

Q: Problem Solving: 1. From the given frame shown it is supported by a hinged at A and a roller at C.…

A:

Q: Transform graphically the figure into one wherein the sides with unknown quantities are made…

A: Solution: Interpretation of Data: Line Bearing Length AB S 86°35' W 607.66 m BC S 31°35' W…

Q: STA BS HI FS IFS ELEV BМ — а 1.24 234.51 m ТР- 1 1.11 3.40 1 + 00 + 25 + 50 + 75 ТР - 2 4.6 2.7 3.6…

A: Height of instrument method HI = elevation + BS elevation = HI - FS

Q: The similar triangle method can be defined as: a. One of the simplest methods used for determining…

A: Triangulation survey is a method in which tracing and measurement of a series or network of…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.