8 holes Ø10 Ø80 Ø40 15 30 Ø100 Ø50

Q: Q / In visual basic is the 4 points extension to represent project file. * frm O vbp

A: A Visual Basic project is not just a single file. Besides the usual Project (. vbp extension) and…

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK Metal…

A: It comes under Engineering Drawing, also known as Engineering Graphics.  For Mechanical Engineering,…

Q: Show Isometric View. Use Dimlinear for measurement

A: Hi! As per the honor code we are not allowed to provide file or link of the file. We are only…

Q: Matching Directions: Match each description of locating points when creating planar entities in the…

A:

Q: Subject: Engineering Drawing or AutoCAD Instruction: Draw the 2D Orthographic Projection (Front,…

A: Asked: To draw the orthographic projections of the given object.   The following tools are used to…

Q: Find the shortest distance from point B to line AC

A:

Q: For the given structures, determine the degree of indeterminacy. 7. A 7

A:

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: DRAW ISOMETR VIEW

A:

Q: Discuss the procedure for performing 2D conformal coordinate transformations?

A: Solution: There are basically 3 steps that are used in the procedure of 2D conformal coordinate…

Q: Find the centroid of the shaded area in the attached file Y k3cm Зст 1cm Зст 1cm 7cm

A: Schematic figure of the above problem:

Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…

A: question being asked here is to draw the above diagram using AUTO CAD program and also clearly…

Q: REQUIRED: ISOMETRIC DRAWING VEN FIGURE SHOWN TOP VIEW syooing 0.5cm FRONT VIEW RIGHT SIDE VIEW 45

A:

Q: You can show the true size views of two planes in a single reference plane? OWhen the planes are…

A: You can show the true size views of two planes in a single reference plane? When the planes are…

Q: TOP VIEW 200 FRONT VIEW SIDE VIEW ORTHOGRAPHIC VIEW

A: Orthographic view is given drawing the isometric view

Q: The coordinates of centroid for the following section is 150 mm - 20 mm 20 mm 20 mm 300 mm 500 mm

A:

Q: Instruction: Dew the 3D Dewing hometric View) of the indicated 2D Orthographic Projection You can…

A: From the given question it is required to draw the 3D drawing of the 2D orthographic projection. for…

Q: From the figure shown, determine the following: y L, L4 CE h, h7 he h2 hs he he Distance of the…

A: To determine Distance of Centroid from x-axis.

Q: Problems 1 and 2. Locate the centroid of the shaded area r 100 mm 100 mm 140 mm 50 mm 140 mm 50 mm…

A: Solution- X= 15.1849 mm Y= 4.25 mm

Q: Draw the 3 Principal Views of the object (units in cm) 5.0 3.0 1.5 R=1.0 1.5 ↓ 1.0 3.0 -2.5 2.0

A: I have draw  Top view.  Front view

Q: What are the type of the following bits?

A: Similarly, NXL impregnated diamond 3-inch core drill bits are designed with a similar principle but…

Q: As a civil engineer student what is the importance of alphabet of lines?

A: The lines in the Alphabet of Lines are used to describe the shape, size, hidden surfaces, interior…

Q: ✔ Part A What is the scale of the USGS 7-1/2 minute quadrangle map? Express your answer as an…

A: A 7-1/2 minute quadrangle map  are the maps produced by photogrammetric analysis that covers an area…

Q: Compare and contrast the types of graphic representtaion.  (Artistic Drawing and Industrial…

A: Technical drawing: It is a system representation of different types of objects or structures. It is…

Q: Flowchart for Solution of Three-Dimensional Truss Problems

A: Flowchart of 3d truss analysis can be used in various programes without worrying much about…