mb: L d ms A horizontal L=1.4 m long mb3D12kg uniform bar is hinged on the left end and pulled at the right end by a cable. The cable makes 30° angle with horizontal. A 22 kg store sign is suspended below the bar at d=0.18 m from the right end. Find the magnitude of horizontal hinge force.

L d- ms A horizontal L=1.3 m long mb=15 kg uniform bar is hinged on the left end and pulled at the right end by a cable. The cable makes 35° angle with horizontal. A 18 kg store sign is suspended below the bar at d=0.10 m from the right end. Find the magnitude of vertical hinge force.

A horizontal L=1.0 m long mb=12 kg uniform bar is hinged on the left end and pulled at the right end by a cable. The cable makes 24° angle with horizontal. A 20 kg store sign is suspended below the bar at d=0.18 m from the right end. Find the magnitude of horizontal hinge force.

A 150 kg uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end. Calculate the magnitude of the vertical and horizontal component of the force that the wall exerts on the left end of the beam if the angle between the cable and horizontal is theta = 36 degrees.

A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath.  The drawbridge weights 55000 N and is 15.0 m long.  A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. What is the tension in the cable? Find the magnitude and direction of the force the hinge exerts on the bridge. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks? What is the angular speed of the drawbridge as it becomes horizontal? What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?

One end of a uniform rod of weight w = 73.5 N and length L = 2.55 m is supported by a cable at an angle of ? = 37.0°above the rod. The other end rests on a small frictionless support and presses into a wall as shown in the figure. Determine the magnitude n of the vertical normal force exerted by the support on the rod and find the magnitude T of the tension in the cable.

A beam with length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board. Suppose the maximum tension that the wire can withstand is 1500 N. What is the maximum load that the hinge can support before the wire breaks?

A uniform ladder weighing 490 N rests against a frictioniess wall. The ladder has a length L = 14.0 m and makes a 59.0° angle with the horizontal ground. An 820 N firefighter has climbed d = 4.20 m along the ladder from the bottom. Find the coefficient of static friction Hs between the ladder and the ground. O 0.863 O 0.225 O 0.119 O 0.332 O 0.567

A 355 N uniform ladder of length L= 8.00 m leans against a smooth (frictionless) wal The ladder mnakes an angle of 50.0° angle with the horizontal ground and the force of static friction keeps the ladder from sliding to the left. An 875 N firefighter has climbed d = 6.30 m along the ladder trom the bottom. What is the force of static friction f, between the ladder and the ground? 50.0 O 119 N O 480 N O 727 N O 567 N command eptien

A 1204-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end A 1515-N crate hangs from the far end of the beam. Find the magnitude of the tension in the wire. The angle theta (9) is 29 degrees and the angle phi () is 53 degrees. The length of the beamis L Вeam ROUND OFF FINAL ANSWER TO THE NEAREST WHOLE NUMBER. INPUT THE SYMBOL OF THE UNIT. NO SPACE BETWEEN THE NUMBER AND THE UNIT.