Match each type of transducer with the corresponding physical phenomenon, law, or property where it is based on Prompts Submitted Answers Inductive Displacement Transducers Choose a match Electromagnetic Flow Transducer Choose a match Potentiometer Transducers Choose a match Elastic Resistive Transducers Choose a match Strain Gauge Transducers Choose a match Capacitive Transducers Choose a match Piezoelectric Transducers Choose a match

Match each type of transducer with the corresponding physical phenomenon, law, or property where it is based on Prompts Submitted Answers Inductive Displacement Transducers Choose a match Electromagnetic Flow Transducer Choose a match Potentiometer Transducers Choose a match Elastic Resistive Transducers Choose a match Strain Gauge Transducers Choose a match Capacitive Transducers Choose a match Piezoelectric Transducers Choose a match

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter11: Thermostats, Pressure Switches, And Other Electric Control Devices

Section: Chapter Questions

Problem 23RQ

See similar textbooks

Similar questions

Given the four statements, which of the following statements are true about an op-amp integrator? i. For an op-amp integrator with R = 100KOhms, C waveform, the output waveform is a cosine waveform. 10UF and a sine wave input %3D ii. For an op-amp integrator with R = 100KOhms, C waveform, thc output waveform is a squarc wave. 10UF and a triangular input %3D %3! iii. For an op-amp integrator with R = 100KOhms, C waveform, the output waveform is a sawtooth waveform. = 10UF and a sine wave input %3D iv. For an op-amp integrator with R 100KOhms, C 10uF and a square wave input waveform, the output waveform is a triangular waveform. Oi, ii, i O i, ii, iv O i iv O ii, ii
Calculate the peak-to-peak inductor current ripple (in amperes) of a Buck converter assuming it operates in continuous current conduction mode. Circuit parameters are: Input voltage Vdc = 38 V, output voltage Vo = 17 V, PWM frequency fpwm = 50 kHz, inductor value 328 µH and capacitor value C = 10 µF. is S iL L I₂ Vac VA D VL ic C R₁ Please specify your answer in units of A to 2 decimal places. V
1.EXPLAIN THE CHARACTERISTICS OF AN OPAMP? 2.WHAT ARE THE CHANGES IN THE AMPLIFICATION DURING LOW FREQUENCY
For the following zener clipper draw the output waveform Vz1 = 5V, Vz1 = 7V VK = 0.8v lkn ISV V₁₂ 5V 2, 72. -5V Q2 Determine The Output Waveform And Calculate The current and PIV 1kQ 1kQ 10 V 10 si www www Q. For the circuit shown in Figure below (1),find the maximum and minimum values of zener diod current. Live 5 ΚΩ www I IL 15 80-120 V 10 ΚΩ LIR 101 102 1015 S Ne 1 k0 www Iz 50 V U2 -ot V. Fumal inash
3Z The most usual form of op-amp package a.type TO-5 metal cans b.integration packages c.dual in-line packages d.type TO-8 metal cans
In a Wien bridge oscillator circuit, resistor and capacitor form a series branch and a parallel branch. The value of the resistor is 200 ohm and the value of the capacitor is 10 mF. Determine the frequency of oscillation for the Wien Bridge oscillator circuit.
The DC-DC converter below is fed from a 96 V DC source and it is desired to obtain 24 V output voltage on 15 2 load resistors. The switching frequency of the converter is 50 kHz. It is desired that the fluctuation rate in the output voltage should not exceed 1%. VI VL mo ic İR a) What is the minimum required coil inductance? b) What is the minimum required capacitor value?
Consider Figure 65. Compute for the minimum value of R3 if R₁ = R₂= 51kohms, C₁-C₂-0.001uF and R4=115.07kohms to start the oscillation. R3= kohms +Vcc Op-amp Output sinusoidal signal -VEE S= 4,1 Figure 65 K₂
Given the four statements, which of the following statements are true about an op-amp integrator? i. For an op-amp integrator with R = 100KOhms, C = 10UF and a sine wave input waveform, the output waveform is a cosine waveform. %3! ii. For an op-amp integrator with R = 100KOhms, C = 10uF and a triangular input waveform, the output waveform is a square wave. iii. For an op-amp integrator with R 100KOhms, C = 10uF and a sine wave input waveform, the output waveform is a sawtooth waveform. %3D iv. For an op-amp integrator with R 100KOhms, C 10UF and a square wave input waveform, the output waveform is a triangular waveform. O i, ii, i O i, i, iv O į iv O i, i
Output of a thermocouple is connected to an op- amp as shown in the figure. THERMOCOUPLE 100 KQ 200 2 METER i FURNACE I (a) Determine the output voltage of the thermocouple if the junction temperatures 01= 82°C and 02 84°C and a = 3.5x10-2, B = 8.2 x 10-6 (b) Determine the output voltage of the op-amp.
please work out the following using the infomation in the attached photo. This is for a Boost converter (a) Output voltage(b) Inductor current ripple (assume it is 20%) (c) Switching frequency (d) Output current (e) Output voltage ripple
Consider the phase shift oscillator in figure below a) Determine the frequency of oscillation for R = 12 kn and C = 150 pF. What is the required value of R2? b) Design the circuit such that the frequency of oscillation is f, = 22 kHz. Let C = 0.001µF. R2 C C R -o vo R ww